Candy 36900571, User Instructions

- 20 -

waste collection service or the shop where the appliance was 

purchased.

  INSTALLATION INSTRUCTIONS

•  Assembly and electrical connections must be carried out 

by specialised personnel.

•  Wear  protective  gloves  before  proceeding  with  the 

installation.

•  Electric Connection:

Note! Verify the data label placed inside the appliance:

- If the symbol   appears on the plate, it means that no earth 

connection must be made on the appliance, therefore follow 

the instructions concerning insulation class II.

- If the symbol   DOES NOT appear on the plate, follow the 

instructions concerning insulation class I.

Insulation class II

- The appliance has been manufactured as a class II, therefore 

no earth cable is necessary. The plug must be easily accessible 

after the installation of the appliance. If the appliance 

is equipped with power cord without plug, a suitably 

dimensioned omnipolar switch with 3 mm minimum opening 

between contacts must be fitted between the appliance and 

the electricity supply in compliance with the load and current 

regulations.

- The connection to the mains is carried out as follows:

BROWN = 

L

 line

BLUE = 

N

 neutral.

Insulation class I

This is a class I, appliance and must therefore be connected to 

an effiecient earthing system.

- The appliance must be connected to the electricity supply as 

follows:

BROWN = 

L

 line

BLUE = 

N

 neutral

YELLOW/GREEN

=   earth.

The neutral wire must be connected to the terminal with the 

N 

symbol while the 

YELLOW/GREEN

, wire must be connected 

to the terminal by the earth symbol  .

When connecting the appliance to the electricity supply, make 

sure that the mains socket has an earth connection. After fitting 

the ducted cooker hood, make sure that the electrical plug is 

in a position where it can be accessed easily. If the appliance 

is connected directly to the electricity supply, an omnipolar 

switch with a minimum contact opening of 3 mm must be 

placed in between the two; its size must be suitable for the 

load required and it must comply with current legislation.

•  

If the hob is electric, gas, or induction, the minimum distance 

between the same and the lower part of the hood must be at 

least 

65 cm

. If a connection tube composed of two parts is 

used, the upper part must be placed outside the lower part. Do 

not connect the cooker hood exhaust to the same conductor 

used to circulate hot air or for evacuating fumes from other 

appliances generated by other than an electrical source. Before 

proceeding with the assembly operations, remove the anti-

grease filter(s) (Fig.7A) so that the unit is easier to handle.

-  In the case of assembly of the appliance in the suction version 

prepare the hole for evacuation of the air.

•  

We recommend the use of an air exhaust tube which has the 

same diameter as the air exhaust outlet hole. If a pipe with a 

smaller diameter is used, the efficiency of the product may be 

reduced and its operation may become noisier.

•  Fixing to the wall:

- Drill the holes 

A

 respecting the distances indicated (Fig.2).

- Fix the appliance to the wall and align it in horizontal position 

to the wall units.

- When the appliance has been adjusted, definitely fix the hood 

using the screws 

A

 (Fig.5).

For the various installations use screws and screw anchors 

suited to the type of wall (e.g. reinforced concrete, plasterboard, 

etc.). If the screws and screw anchors are provided with the 

product, check that they are suitable for the type of wall on 

which the hood is to be fixed.

•  Fixing the decorative telescopic flue:

- Arrange the electrical power supply within the dimensions 

of the decorative flue. If your appliance is to be installed in the 

ducting version or in the version with external motor, prepare 

the air exhaust opening.

- Adjust the width of the support bracket of the upper flue 

(Fig.3).

- Then fix it to the ceiling using the screws 

A

 (Fig.3) in such a 

way that it is in line with your hood and respecting the distance 

from the ceiling indicated in Fig.2.

- Connect the flange 

C

 to the air exhaust hole using a 

connection pipe (Fig.5).

- Insert the upper flue into the lower flue.

- Fix the lower flue to the hood using the screws 

B

 provided 

(Fig.5), extract the upper flue up to the bracket and fix it with 

the screws 

B

 (Fig.3).

- If your appliance has the lower connections indicated as in 

Fig.4A, the fixing to be carried out is that shown in Fig.6A.

To transform the hood from a ducting version into a filtering 

version, ask your dealer for the charcoal filters and follow the 

installation instructions.

•  Filter hood:

Please note:

- In order to transform the hood from 

EXTRACTOR HOOD

 into

FILTER HOOD

 the active carbon filters must be ordered at your 

distributor as accessory.

We have two different types of Kit, one with non-regenerable 

active carbon filters (Fig.7B) and the other one with 

regenerable active charcoal filters (washable) (Fig.7C).

- To replace the non-regenerable active carbon filters 

X

, pull 

lever outwards as shown in Fig.7B.

  USE AND MAINTENANCE

•  

We recommend that the cooker hood is switched on before 

any food is cooked. We also recommend that the appliance is 

left running for 15 minutes after the food is cooked, in order 

to thoroughly eliminate all contaminated air. The effective 

performance of the cooker hood depends on constant 

maintenance; the anti-grease filter and the active carbon filter 

both require special attention.

•  The anti-grease filter

 is responsible retaining the grease 

particles suspended in the air, therefore it is subject to clogging 

with variable frequency according to the use of the appliance.

-  To prevent the danger of possible fires, at least every 2 

months one must wash the anti-grease filters by hand using 

non-abrasive neutral liquid detergents or in the dishwasher 

at low temperatures and on short cycles.

-  After a few washes, colour alterations may occur. This does 

not give the right to claim their replacement.

•  The active carbon filters

 are used to purify the air that is 

sent back into the room and its function is to mitigate the 

unpleasant odours produced by cooking.

-  The non-regenerable active carbon filters must be replaced 

at least every 4 months. The saturation of the active charcoal