Candy CD 650, User Instructions

27

N.B.: 

Should any of the situations occur and should the machine give a bad wash performance, it is

necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the
deposits which a second wash in the machine would not be able to remove.

If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.
This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee. 
This information will make it possible to take more effective action more quickly.

The manufacturers decline any responsability for any printing mistakes in this instruction booklet. They also reserve the right to modify their
own appliances as necessary without altering the essential characteristics.

FAULT

CAUSE

REMEDY

8 - Load of dishes is only 

partially washed 

9 - Presence of white spots 

on dishes

10 - Noise during wash

11 - The dishes are not 

completely dry

See causes for no. 5

Bottom of saucepans have not
been washed well

Edge of saucepans have not 
been washed well

Spray arms are partially blocked

The dishes have not been 
properly loaded

The end of the outlet hose is in
the water

The incorrect amount of 
detergent has been measured
out; the detergent is old and hard

The wash programme is not 
thorough enough

The lower basket dishes have
not been washed

Water is too hard

The dishes knock against one
another

The revolving arms knock against
the dishes

Inadequate air flow

Check

Burnt on food remains must 
be soaked before putting pans
in dishwasher

Reposition saucepans

Remove spray arms by
unscrewing ring nuts clockwise
and wash under running water

Do not place the dishes too 
closely together

The end of the outlet hose 
must not come into contact 
with the outflow water

Increase the measure 
according to how dirty the
dishes are and change detergent

Choose a more vigorous 
programme

Depress half load button

Check salt and rinse aid level
and regulate amount. 
Should the fault persist, 
Contact Service Centre

Load dishes better onto the
basket

Load dishes better

Leave the dishwasher door ajar
at the end of the wash program
to allow the dishes to dry naturally

26

Identifying minor faults

Warning!
Before removing any panel:

1. Turn the knob to STOP.
2. Pull the electric plug out.

Should  the  dishwasher  fail  to  operate,  before  contacting  the  Service  Centre, make the
following checks:

FAULT

CAUSE

REMEDY

1 - Machine completely dead 

2 - Machine does not 

draw water

3 - Machine does not 

discharge water

4 - Machine discharges water

continuously

5 - Spray arms are not heard

to rotate

6 - On electronic appliances

without a display: “eco”indi-
cator light  and indicator light
“No.1” with audible signal
are heard.

7 - On electronic appliances with

a display: “E1” appears on the
display with audible signal.

Plug is not connected to wall
socket

O/I button has not been pressed

Door is open

No electricity

See causes for no. 1

Water tap is turned off

Programme selector is not at
correct position

The inlet hose is bent

The inlet hose filter is not 
correctly connected

Filter is dirty

Outlet hose is kinked

The outlet hose extension is
not correctly connected

The outlet connection on the
wall is pointing downwards not
upwards

Position of outlet hose is too
low

Excessive amount of detergent

Item prevents arms from rotating

Plate and cup filter very dirty

Water inlet tap turned off

Water inlet tap turned off

Connect electric plug

Press button

Close door

Check the fuse in the plug and 
the electricity supply

Check

Turn water tap on

Turn programme selector to
correct position

Eliminate the bends in the hose

Clean the filter at the end of the
hose

Clean filter 

Straighten outlet hose

Follow the instructions for 
connecting the outlet hose
carefully

Call a qualified technician

Lift outlet hose to at least 40 cm
above floor level

Reduce amount of detergent 
Use suitable detergent

Check

Clean plate and cup filter

Switch off the appliance.
Turn on the tap.
Re-set the cycle.

Switch off the appliance.
Turn on the tap.
Re-set the cycle.