11
11
ELECTRICAL SECTION
2
IMPORTANT: Installation must
be carried out according to the
manufacturer’s instructions.
Incorrect installation may cause harm
and damage to people, animals or
property, for which the manufacturer
accepts no responsibility.
Before carrying out any work on the
electrical section of the appliance,
it must be disconnected from the
mains.
Connection to a good earth wiring
system is absolutely essential.
The manufacturer accepts no
responsibility for any inconvenience
caused by failure to comply with this
rule.
Before carrying out any work on the
electrical section of the appliance,
it must be disconnected from the
mains.
If the hob surface is cracked
disconnect the appliance from the
mains and contact the After-Sales
Service.
GENERAL
•
Connection to the electric power
supply must be carried out by a
qualified technician and following the
appropriate safety regulations.
•
The appliance must be connected to
the mains checking that the voltage
corresponds to the value given in the
rating plate and that the electrical
cable sections can withstand the load
specified on the plate.
•
If the hob is supplied without plug, fit
a standard plug which is suitable for
the power absorbed by the appliance
and in conformity with the local rules
in force.
•
The colours of the wires in the
appliance power cable may not
correspond with the colours marked
on the terminals of your electrical plug.
The plug should always be wired as
follows:
– connect the green/yellow wire to the
terminal marked with the letter
E
or
the earth symbol or coloured
green/yellow;
– connect the blue wire to the terminal
marked with the letter
N
or coloured
black;
– connect the brown wire to the
terminal marked with the letter
L
or
coloured red.
•
The plug must be connected to an
outlet connected to the grounding unit
in conformity to security norms.
•
If the appliance is to be connected
directly to the mains, it must be placed
with an omnipolar switch with minimum
opening between the contacts of 3 mm
between the appliance and the mains
•
The power supply cable must not touch
the hot parts and must be positioned
so that it does not exceed 50°C above
ambient.
•
Once the appliance has been installed,
the power switch or power plug must
always be in a accessible position.
•
If the power supply cable is damaged it
must be substituted by a suitable cable
available in the after sales service.
•
The appliance must have its own
supply; any other appliances installed
near it must be supplied separately.
•
N.B. For connection to the mains,
do not use adapters, reducers or
branching devices as they can
cause overheating and burning.
In the event that installation should
require modifications to the mains supply
wiring system, it is recommended that a
qualified technician be called to carry out
substitution.
The technician will also have to verify that
the cross-section of the electric cables
on the power point match the appliance’s
power rating.
Summary of Contents for CE32XK
