26
26
PAINTED PARTS AND SILKSCREEN PRINTED SURFACES
Clean using an appropriate product. Always dry thoroughly.
IMPORTANT:
these parts must be cleaned very carefully to avoid scratching and abrasion.
You are advised to use a soft cloth and neutral soap.
CAUTION: Do not use abrasive substances or non-neutral detergents as these will
irreparably damage the surface.
Note: Continuous use may cause a change in the glaze around the burners,
corresponding to the areas exposed to the heat.
GAS TAPS
Do not let cleaning products come into contact with the valves.
Periodic lubrication of the gas taps must be carried out by specialist personnel only.
In the event of operating faults in the gas taps, call the Service Department.
BURNERS AND PAN SUPPORTS
These parts must be cleaned using a sponge and soapy water or other suitable non-
abrasive products. Dry with a soft cloth.
Warning! Not dishwasher safe.
After cleaning, the burners and their flame spreaders must be well dried and correctly
replaced.
It is very important to check that the burner flame spreader and the cap have been correctly
positioned. Failure to do so can cause serious problems.
Check that the electrode “
S
” (figs. 3.1, 3.3) next to each burner is/are always clean to
ensure trouble-free sparking.
Check that the probe “
T
” (figs. 3.1, 3.3) next to each burner is/are always clean to ensure
correct operation of the safety valves.
Both the probe and ignition plug must be very carefully cleaned.
Note: To avoid damage to the electric ignition do not use it when the burners are not
in place.
CORRECT REPLACEMENT OF THE SEMI-RAPID AND RAPID BURNER
It is very important to check that the burner flame distributor “
F
” and the cap “
C
” have been
correctly positioned (see figs. 3.1, 3.2) - failure to do so can cause serious problems.
CORRECT REPLACEMENT OF THE DOUBLE-RING (Some models only)
The burner must be correctly positioned; failure to do so can cause serious problems.
Fit the flame spreader to the housing as shown by the arrows (see figs. 3.3, 3.4, 3.5).
The burner correctly positioned must not rotate (fig. 3.5).
Note: Continuous use may cause a change in the glaze around the burners and
grids, corresponding to the areas exposed to the heat. This is a natural phenomenon
and does not prevent the parts from working properly.
Summary of Contents for DOMINO Series
