background image

10849.PDF

9

80mm Minimum Insert

 

the minimum insert depth that the seat post must be inserted into the frame is 80mm.   seat 

posts are  permanently marked with ‘minimUm insert” line 80mm up from the bottom of an 

un-cut seat post.  

Cutting the Seat Post

in some frames (especially smaller sizes), a seat post will only be able to be inserted into a seat tube 

to a maximum depth of 100 mm.   Below a depth of 100mm carbon material can interfere with the 

seat post.  the material can not be removed. 

  

the full length of the seat post can be cut down to have sufficient adjustment range.   the  minimum 

insertion depth requirement of 80mm does not change.  80mm should be marked from the bottom 
of a cut seat post.  

the seat post may be cut (shortened).   a new “minimUm insert”  line 80mm 

from the bottom of the post must be marked or indicated without scoring, scratching or 

otherwise damaging the surface of the seat post.  Use a thin decal  (automotive pin striping) or 

permanent marker.

WARNINGS

TO AVOID SERIOUS SEAT POST OR FRAME DAMAGE:

1.  after any crash, fall, or impact, remove and inspect the seat post for damage (e.g., cracks, 

scratches,  scrapes,  gouges,  splintering).    if  damage  is  found,  do  not  ride  it;  discard  it. 

replace the seat post with a new one.

2.  Do not  use solvents, or chemical spray cleaners to clean.  

3.  never force a seat post into the seat tube.  

4.  Use a good torque wrench to tighten fasteners to the specified torque.  Correct tightening 

torque of the seat post clamp and the bolts that hold the saddle to the seat post is also 

very important to your safety. always tighten seat post to saddle clamp bolts to the correct 

torque. Bolts that are too tight can stretch and deform. Bolts that are too loose can move, 

fatigue and fracture. either mistake can lead to a sudden failure of these bolts. such a 

failure may lead to an accident, with risk of serious injury, paralysis or death.

5.  if  the  seat  post  requires  cutting,  have  it  done  by  a  professional  bike  mechanic  with 

experience cutting high-performance carbon components.  

YOU  CAN  BE    SEVERELY  INJURED,  PARALYZED  OR  KILLED  IF  YOUR  IGNORE  THESE 

WARNINGS.

Summary of Contents for Slice Carbon






















Reviews: