background image

4-10

Chapter 4   Other Functions

4.

User Mode Functions

The following functions are available in the User Mode.

Buzzer (Beeper) Control Setting

The beeper (“buzzer”) sounds when you press the control 
panel keys and when a scanning error occurs.

ON2:

 The beeper sounds when a scanner error occurs, and 

when a control panel key is pressed.

ON1:

 The beeper sounds when a scanner error occurs.

OFF:

 The beeper never sounds.

Double-Feed Control Setting

Select whether double-feed detection is enabled when the 
Count-Only mode is enabled. If you set DBL Feed Control 
to [ON], double feeds are detected during feeding in the 
Count-Only mode. 

(See “Double-Feed Detection” on 

p. 4-5.)

Staple Detection Setting

Select whether staple detection is enabled when the Count-
Only mode is enabled. 

(See “Staple Detection” on p. 4-6.)

ON:

 Detects staples in the Count-Only mode.

OFF:

 Does not detect staples in the Count-Only mode.

Staple Detection Level Setting

Sets the staple detection sensitivity level.
[1] is the default setting, [2] provides higher sensitivity, 
and [0] provides lower sensitivity.

Long Document Mode Setting

You can enable this mode to detect and scan document 
pages up to 118.11" (3 m) long when the Auto Detection 
page size setting is selected. 

(See “Long Document Mode 

Setting” on p. 3-4.)

ON2: 

Automatically detects page sizes when scanning 

documents up to 118.11" (3 m) long.

ON1:

 Automatically detects page sizes when scanning 

documents up to 39.37" (1 m) long.

OFF:

 Automatically detects page sizes when scanning 

documents up to 17.01" (432 mm) long.

Hint

Feeding a document longer the maximum detectable page size 
for Auto Detection causes a paper jam indication, and transport 
stops.

Summary of Contents for 3622B002



























































































































































Reviews: