Chapter 17
17-42
9. COLOR
Adjustment for color balance
T-17-33
10. HV-PRI
Primary Charging Assembly Output Adjustment
T-17-34
COPIER>ADJUST>COLOR
Sub item
Description
Level.
ADJ-Y/M/C/K
Adjust the color balance of Y/M/C/K colors for users.
Change the default value of the color balance when the output density varies by machine. Setting a larger value increases
density. Setting a smaller value decreases density.
Setting range: -8 to 8
[Factory setting value/Value after RAM clear: 0]
1
OFST-Y/M/C/K
Adjust the density and color balance of the bright part of Y/M/C/K colors.
Offset the color balance of the bright part when the document base is not normally read. Setting a larger value increases
the color balance. Setting a smaller value decreases the color balance.
When the base is not normally eliminated and it looks like a fogging image, decrease the value until the fogging becomes
invisible.
Setting range: -32 to 32
[Factory setting value/Value after RAM clear: 0]
1
LD-OFS-Y/M/C/K
Adjust the color balance of low density area.
Be sure not to use this item in normal operation.
Setting range: -8 to 8
[Factory setting value/Value after RAM clear: 0]
2
MD-OFS-/Y/M/C/K
Adjust the color balance of middle density area.
Be sure not to use this item in normal operation. (recommended setting value: -1)
Setting range: -8 to 8
[Factory setting value/Value after RAM clear: 0]
2
HD-OFS-Y/M/C/K
Adjust the color balance of high density area.
Be sure not to use this item in normal operation. (recommended setting value: -2)
Setting range: -8 to 8
[Factory setting value/Value after RAM clear: 0]
2
COPIER>ADJUST>HV-PRI
Sub item
Description
Level.
OFSTAC-Y
Offset value for the charging AC current at a constant speed (Y)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-M
Offset value for the charging AC current at a constant speed (M)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-C
Offset value for the charging AC current at a constant speed (C)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-K
Offset value for the charging AC current at a constant speed (K)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-Y2
Offset value for the charging AC current at a 1/2 speed (Y)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-M2
Offset value for the charging AC current at a 1/2 speed (M)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-C2
Offset value for the charging AC current at a 1/2 speed (C)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-K2
Offset value for the charging AC current at a 1/2 speed (K)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-Y3
Offset value for the charging AC current at a 1/4 speed (Y)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
OFSTAC-M3
Offset value for the charging AC current at a 1/4 speed (M)
When a sanded image occurs, increase the value until an appropriate image is obtained.
Setting range: 0 to 5 (When incremented by 1, the value changes by 50muA.)
[Factory setting value/Value after RAM clear: 0]
1
Summary of Contents for CiRC2550
