Chapter 17
17-75
2. USER
T-17-54
PT-W-SET
Change of pre-rotation band image width when color OHT paper passes through
This increases the band amount when rattling noises are heard from the ITB cleaner blade when color OHT paper passes
through in order to minimize these noises.
Setting range: 0 to 10 (in 10 mm increments)
[Factory setting/value after clearing RAM: 5]
2
FLYING
Setting whether to initiate a flying start
This is set to "1" when a flying start is not to be initiated in consideration of the service life of the fixing unit. Normally,
after a job is completed, operation is controlled so that the fixing is performed and the takes of the polygons are made
longer in preparation for the next job, but this control is not performed when the item is set to "1."
Settings
0: A flying start is initiated.
1: A flying start is not initiated.
[Factory setting/value after clearing RAM: 0]
2
PP-LWRT
Not used
2
USB-RCNT
Setting for automatic connection when USB device is disconnected
This sets whether automatic re-connection is to be initiated when the USB device is disconnected (USB reconnect).
Settings
0: No automatic connection
1: Automatic connection is initiated.
[Factory setting/value after clearing RAM: 0]
2
MIBCOUNT
Charging counter MIB switch
Change the scope range of the charging counter MIB.
Setting range
0: Display all charging counter MIB information.
1: Display all charging counter MIB information that is displayed in LUI.
2: Do not display charging counter MIB information.
Method of Adjustment
When the charging counter MIB is not disclosed, request a serviceman to change the counter value.
[Value after execution of RAM clear: 0]
2
MEAP-PRI
Changes the MEAP task priority.
If it is set to ON, the MEAP task priority is upgraded.
Use case
When MEAP performance improvement is needed.
Setting values
0: OFF (default), 1: ON
[Factory setting / Value after clearing RAM: 0 (S3500: 1)]
2
PDLEVCT1
Event skip setting for PDL continuous jobs
Skips some status information (event skip) sent to PDL-PIPIT in CPCA layer to speed a PDL continuous job. This mode
is used to set the status information to be skipped.
Note that this setting may cause inconsistency in UI display. Therefore, this mode is provided as a service switch for
service engineers to turn OFF the skip setting (PDLEVCT1 shows the CPCA event(s) or status(es) to be skipped.)
Use Case
When receiving complaints concerning status information shown in UI.
Setting values
0: No event skipped
1: Skip Job status / Job list change information
Note that statuses of interaction / executing / complete are excluded in execution.
2: Skip job status / job list change information
Note that statuses of interaction are excluded in execution.
(Performance will be improved in the order of 0, 1 and 2.)
[Factory setting / Value after clearing RAM: 0]
2
PROXYRES
Switches whether to make a proxy response to an inquiry via Windows.
Switch the setting when an accurate status should return to an inquiry via Windows, not to make a proxy response during
sleep.
Use case
When an accurate status should return to an inquiry via Windows.
Setting values
0: Not make a proxy response
1: Make a proxy response (default)
[Factory setting / Value after clearing RAM: 0]
2
COPIER>OPTION>USER
Specification selection related to user mode
Sub item
Description
level.
COPY-LIM
Used to change upper limit value setting for number of sheets to copy.
Setting values
1 to 999 sheets [Factory default/After RAM clear: 999]
1
COPIER>OPTION>BODY
Sub item
Description
level.
Summary of Contents for CiRC2550
