Chapter 2
2-7
Correction] > [Full Correction]
6) When 'Test Print1' is displayed, press [OK].
Test Print 1 is output. (It takes approx, 3min.)
7) Follow the instruction on a control panel and set the test print 1 on the copyboard glass.
8) Close the feeder.
9) Press [OK].
Test Print 1 is read.
10) When 'Test Print 2' is displayed, press [OK].
Test Print 2 is displayed.
11) Follow the instruction on a control panel and set the test print 2 on the copyboard glass.
12) Close the feeder.
13) Press [OK].
Test Print 2 is read.
14) When the auto adjustment window is displayed, remove the test print 2 from the copyboard glass.
15) Exit [Additional Func].
2.3 Checking the Connection to the Network
2.3.1 Setting Up the Network
0019-0679
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER C1030 / Color imageRUNNER C1030iF
1) Turn OFF the main power switch.
2) Connect the network cable with the host machine to turn ON the main power switch.
3) Inform the system administrator at the installation site that the host machine installation is complete and request the network settings of the host machine.
4) When the network settings are complete, turn OFF and then ON the main power to enable the settings.
2.3.2 Procedure for Ping Operation
0019-0680
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER C1030 / Color imageRUNNER C1030iF
1) Select the PING command in additional function mode.
[Additional Func] > [System Management] > [Network Settings] > [TCP/IP Settings] > [IPv4 Settings] > [PING Command]
2) Using the control panel keypad, enter the PING command and press [OK].
Enter the IP address of the connected PC in PING command.
The message to indicate presence/absence of reply from the host is displayed.
2.3.3 Checking with Remote Host Address
0019-0682
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER C1030 / Color imageRUNNER C1030iF
1) Inform the system administrator that you will check the network connection using Ping.
2) Check the remote host address with the system administrator.
3) Enter the remote host address to Ping.
- In the case of 'Reply from the host', connection to the network is working.
- In the case of 'No reply from the host', connection to the network is not working so execute the troubleshooting in the following section.
2.3.4 Troubleshooting Network Connection
0019-0683
imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER C1030 / Color imageRUNNER C1030iF
In the case of connection failure to the network, there can be the following causes:
a. The connection between the network and the main controller PCB is faulty
CAUTION:
Perform this item only when connecting to the network.
CAUTION:
Make the following setting only in the case of a user network environment
is TCP/IP.
NOTE:
Check to see that the Ping setting is normally made with the Ping function.
NOTE:
You can check whether the connection to the network is successful or failed
by executing Ping with the remote host address. Remote host address: the IP
address of the PC terminal connecting/operating with the TCP/IP network
environment that connects the host machine.
CAUTION:
Perform this item only when connecting the host machine to the network.
Summary of Contents for Color imageRUNNER C1022
