Chapter 12
12-4
12.2.2 Signal-Sided Print and 2nd Side of a Double-Sided Print
When making a single-side print or printing on the 2nd side of a double-side print, the counter reading is
incremented when the trailing edge of paper leaves the machine, as indicated by the output of the following
sensor:
T-12-2
12.2.3 Side of a Duplex Print (duplex model only)
The machine identifies the end of printing on the 1st side of a double-sided print and increments the counter
reading when the duplex pickup sensor (PS24) goes ON.
12.3 Fans
12.3.1 Outline
The names and functions of the fans equipped to the machine are shown in the table below.
T-12-3
Condition
Sensor
Finisher absent
face-down delivery (center tray):
center delivery tray full sensor (PS8)
face-down delivery (copy tray):
face-down delivery sensor 2 (PS6)
face-up delivery (side tray):
fixing delivery sensor (PS25)
Finisher present
finisher delivery sensor
Symbol Name
Function / Other
FM1
Power Supply Exhaust Fan 1
Exhaust heat in the power supply unit.
FM2
Fixing Exhaust Fan
Exhaust heat in the fixing unit
FM3
Main Body Exhaust Fan
Exhaust heat in the main body.
FM4
Cleaner Fan
Ease heat in the main body.
FM5
Delivery Cooling Fan
Cool the paper being delivered.
FM6
Manual Feeder Cooling Fan
Cool the paper being fed manually.
FM7
Controller Cooling Fan
Cool the controller.
FM8
Delivery Vertical Path Cooling Fan
Cool the delivery vertical path.
FM9
IH Power Supply Cooling Fan
Cool the IH power supply unit.
FM10
Power Supply Exhaust Fan 2
Exhaust heat in the power supply unit.
FM11
ITB Power Supply Cooling Fan
Cool the intermediate transfer unit.
FM12
Face-down Tray Cooling Fan (Front)
Cool the paper being delivered.
FM13
Vertical Path Delivery Exhaust Fan
Exhaust heat in the main body.
FM14
Face-down Tray Cooling Fan (Rear)
Cool the paper being delivered.
Summary of Contents for Color imageRUNNER C5180 Series
