Chapter 2
2-2
2) Make the following selections to highlight [SENS-
IN]; FEEDER>FUNCTION>SENS-IN.
3) Press the OK key.
In response, the machine will run an automatic
adjustment session, and will indicate 'OK!' if it ends
normally.
4) When done, end service mode.
2.1.4
Tray Width
0003-3042
To adjust the tray width, go through the steps
under either "1. AB-Configuration" or "2. Inch-
Configuration."
1. AB-Configuration
1) Turn on the host machine, and start its service
mode.
<Starting Service Mode>
Press the User Mode key; press the 2 and 8 keys at the
same time; then, press the User Mode key once
again.
2) Touch the following in sequence on the screen to
bring up the Adjustment screen:
FEEDER>FUNCTION>TRY-A4.
3) Move the tray side guide to the index A4/A3.
4) Press the OK key to register the A4 width.
5) Move the tray side guide to the index A5R.
6) Touch [TRY-A5R] to highlight.
7) Move the tray side guide to the index A5R.
8) Press the OK key to register the A5R width.
9) Press the Reset key twice to end service mode.
10) Turn off the host machine's control panel power
switch and main power switch in sequence.
11) Turn on the host machine's main power switch.
2. Inch-Configuration
1) Turn on the host machine, and start its service
mode.
<Service Mode>
Press the User Mode key, and press the 2 and 8 keys
at the same time; then, press the User Mode key
once again.
2) Touch the following in sequence on the screen to
bring up the Adjustment screen:
FEEDER>FUNCTION>TRY-LTR.
3) Move the tray side guide to the index LTR/11x17.
4) Press the OK key to register the LTR width.
5) Touch [TRY-LTRR] to highlight.
6) Move the tray side guide to the index STRM/
LTRR/LGL.
7) Press the OK key to register the LTRR width.
8) Press the Reset key twice to end service mode.
9) Turn off the host machine's control panel power
switch and main power switch in sequence.
10) Turn on the host machine's main power switch.
2.1.5
Eliminating the Tilt
0003-1846
Be sure you have adjusted the angle of the ADF
before starting the following adjustment:
1) Loosen the nut [1] found at the rear of the left hinge;
then, turn the hex bolt [2] so that the fixing member
[3] is as far as the line marking [4].
- turn the bolt clockwise to move the member ahead.
- turn the bolt counterclockwise to move the member
in reverse.
2) Tighten the nut.
Summary of Contents for DADF-M1
