background image

3-25

Chapter 3   Basic Operation

IMPORTANT

When a double feed is detected, the following process occurs, and 
messages appear according to the Rapid Recovery System setting 
in the ISIS/TWAIN driver

(See “[Rapid Recovery System] Check 

Box” on p. 8-18.)

• When the Rapid Recovery System is disabled, images scanned 

before the double feed are saved as files, scanning finishes, and 
the following error message is displayed. 

When detecting double feeds by document length

When detecting double feeds ultrasonically

• When the Rapid Recovery System is enabled, scanning pauses 

when a double feed is detected, and the following error message 
is displayed.

When the Rapid Recovery System is Disabled

Return the double-fed document pages to the top of the 
document stack yet to be scanned, and resume scanning.

When the Rapid Recovery System is Enabled

1.

Check the double-fed document page(s).

Hint

• If attached paper, such as a label on the document page, 

appears to be the cause of the double-feed detection, ignore 
the detection.

• If two document pages were fed together, rescan the double-

fed pages.

2.

Press [

] or [

] to select [IGNORE] or [RETRY] 

and press the [Enter] key.

[IGNORE]:

Saves the image of the page that was detected as a double 
feed, and resumes scanning.

[RETRY]:

The display panel appears as below. Return the double-fed 
document pages to the tray and press the Start key.

IMPORTANT

• Press the Start key the erase the image that was being 

scanned when double feeding was detected, and resume 
scanning.

• If you press the Stop key, the images of pages prior to the 

double feed being detected are saved and the scan ends. In 
this case, restart scanning from the document page where the 
double feed is detected, or from the beginning. 

Summary of Contents for DR-9050C - imageFORMULA - Document Scanner



























































































































































Reviews: