background image

2

FCC REGULATIONS (For 120V model)

Check Reader, Model 6130110/6130120
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 
may not cause harmful interference, and (2) this device must accept any interference received, including interference 
that may cause undesired operation.

Note: 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures: 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
- Consult the dealer or an experienced radio/TV technician for help. 
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes 
or modifications should be made, you could be required to stop operation of the equipment. 
Canon U.S.A. Inc.
One Canon Park, Melville, NY 11747, U.S.A.
Tel. No. (800)652-2666

RADIO INTERFERENCE REGULATIONS (For 120V models)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in 
the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry Canada.

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For 120V 
models)

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe 
B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par l’Industrie Canada.

International ENERGY STAR

®

 Office Equipment Program

As an ENERGY STAR

®

 Partner, CANON ELECTRONICS INC. has determined that this machine meets 

the ENERGY STAR

®

 Program guidelines for energy efficiency.

The International ENERGY STAR

®

 Office Equipment Program is an international program that 

promotes energy saving through the use of computers and other office equipment. The program backs 
the development and dissemination of products with functions that effectively reduce energy 

consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are 
office equipment, such as computers, monitors, printers, fax, machine, copiers, and scanners. The standards and logos 
are uniform among participating nations.

This model doesn’t provide “setting options” for power management.

European Union (and EEA) only.

This symbol indicates that this product is not to be disposed of with your household waste, according to 
the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to a 
designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product 
or to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper 
handling of this type of waste could have a possible negative impact on the environment and human 

health due to potentially hazardous substances that are generally associated with EEE. At the same time, your 
cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more 
information about where you can drop off your waste equipment for recycling, please contact your local city office, 
waste authority, approved WEEE scheme or your household waste disposal service. For more information regarding 
return and recycling of WEEE products, please visit www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)

Für EMVG

Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und Gewerbebereich sowie in Kleinbetrieben 
vorgesehen.

Model Names

The following names may be provided for the safety regulations in each sales region of the Check Reader.
CR-L1: 6130110
CR-L1 UV: 6130120

Trademarks

• Canon and the Canon logo are registered trademarks, of Canon Inc. in the 

United States and may also be trademarks or registered trademarks in other 
countries.

• imageFORMULA is a trademark of CANON ELECTRONICS INC.
• Microsoft, Windows, Windows 7, Windows 8.1 and Windows 10 are registered 

trademarks or trademarks of Microsoft Corporation in the United States and 
other countries.

• Microsoft product screen shot(s) reprinted with permission from Microsoft 

Corporation.

• Adobe and Adobe Reader are registered trademarks or trademarks of Adobe 

Systems Incorporated in the United States and other countries.

• Other product and company names herein are, or may be, the trademarks of 

their respective owners.

Copyright

Copyright 2018 by CANON ELECTRONICS INC. All rights reserved.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, 
including photocopying and recording, or by any information storage or retrieval system without the prior written 
permission of CANON ELECTRONICS INC.

Reproduction Warning

This device is designed to be used in a legal manner, in accordance with all applicable laws, including, but not limited 
to, counterfeit and copyright laws, as well as laws pertaining to national security.
Any person(s) found to have reproduced any of the following materials (regardless of whether such reproduction was 
intentional or not) for the purpose of misrepresenting such material as the original may be prosecuted in accordance 
with the applicable laws and regulations.
• Paper money or bank notes (domestic and foreign)
• Postage stamps, revenue stamps, or other similar stamps
• Stock certificates, bond certificates, promissory notes, cheques, or other valuable certificates
• Passports, licenses, or other certificates or documents issued by government officials or agencies
This is not an exhaustive list.
Canon is not responsible for how this scanner is used by an individual. 
Please note that certain intellectual property is protected by copyright law, and copyrighted items may not be 
reproduced without the express permission of the copyright holder except for personal or household use under limited 
circumstances.

Summary of Contents for imageFORMULA CR-L1

















































Reviews: