Cause
Corrective Action
Paper could not be advanced correctly during ejection.
Clearing a Jammed Sheet, Fed Manually
Cannot cut paper.
Cannot cut paper.
Cause
Corrective Action
There are sheets left on the Ejection
Guide.
1.
Press the
OK
button and remove the paper.
2.
Load paper.
There is a foreign object by the Out-
put Tray, obstructing the Cutter Unit.
Lift the Top Cover and remove the foreign object.
You are not using the printer under
the recommended environmental
conditions for the paper.
Use the printer only where the recommended environmental conditions for the paper are met.
Note that various environmental conditions are recommended for various types of paper. For de-
tails on the recommended environmental conditions, see the
Paper Reference Guide
.
Displaying the Paper Reference Guide
You are using paper that is not com-
patible with automatic cutting.
1.
Specify
Manual
as the cutting method and use scissors or a cutting tool to cut the roll.
Specifying the Cutting Method for Rolls
For information about paper that is compatible with automatic cutting, see the
Paper Refer-
ence Guide
.
Displaying the Paper Reference Guide
2.
Press the
OK
button and remove the paper.
In other cases, the Cutter Unit may
be damaged.
Contact your Canon dealer for assistance.
End of paper feed.
End of paper feed.
Cause
Corrective Action
Although an attempt was made to advance the paper manually, it reached the limit posi-
tion that can be advanced.
Canceling manual advancing.
Borderless printng not possible.
Borderless printng not possible.
Cause
Corrective Action
The print job received speci-
fies a type or width of paper
that is not compatible with
borderless printing.
Follow these steps to change the settings of the print job to enable borderless printing.
1.
Press
▲
or
▼
to select
Stop Printing
, and then press the
OK
button.
2.
Make sure the correct printer driver for the printer is selected and try printing again.
For information on types of paper compatible with borderless printing, refer to the
Paper Reference
Guide
.
Displaying the Paper Reference Guide
Press
▲
or
▼
to select
Print With Border
, and then press the
OK
button to continue printing. The docu-
ment will be printed with a border.
The loaded paper is a size
not compatible with border-
less printing.
Press
▲
or
▼
to select
Stop Printing
, and then press the
OK
button.
Replace the paper with paper compatible for borderless printing as follows.
1.
Press
▲
or
▼
to select
Change Paper
, and then press the
OK
button.
Removing the Roll from the Printer
Removing Rolls From the Roll Holder
2.
Replace the paper with paper compatible for borderless printing.
Loading Rolls on the Roll Holder
The printer now starts printing the print job.
For information on types of paper compatible with borderless printing, refer to the
Paper Reference
Guide
.
Cannot cut paper.
iPF6400SE
Error Message
Messages regarding paper
648
Summary of Contents for imagePROGRAF iPF6400SE
