Canon IMAGERUNNER 7095 PRINTER Service Manual Download | Manualshive

Page: 229 / 615

background image

Chapter 7

7-52

7.10.19.4 Stringing the Charging Wire

0010-8939

As a rule, the charging wire (except the grid wire)
may be strung in the same way for all charging as-
semblies. The following uses the primary charg-
ing assembly as an example:
1) Remove the 2 screws [1], and detach the

shielding plate (left, right) [2] of the charging
assembly.

To prevent deformation (slack) of the primary

charging assembly, be sure to work on the left
and right shielding plates separately. (Do not
loosen the screw for the left/right shielding
plate.)

2) Remove the wire cleaner.

F-7-132

For other charging assemblies, remove the lid (2
pc.)

3) Free a length of about 5 cm from a charging

wire reel (wire dia. of 0.06 mm), and form a
loop at the end about 2 mm in diameter.

F-7-133

MEMO:

To form a loop, wind the charging wire once
around a hex key, and twist the key 3 to 4 times.

4) Cut the end (excess) for the twisted charging

wire.

5) Hook the loop on the stud.
6) Hook the charging wire on the charging wire

positioner at the rear, and hook the charging
wire tension spring on the charging wire, and
twist it.

F-7-134

7) Cut the excess of the charging wire with a

nipper.

8) Pick the end of the charging wire tension

spring with tweezers, and hook it on the
charging wire terminal. In the case of the pre-
transfer charging assembly, hook the spring at
the front.

F-7-135

Be sure of the following:
- The charging wire is free of bends and twists.
- The charging wire is in the bottom of the V-

groove of the charging wire positioner.

F-7-136

9) Fit the cushion to the front of the charging

wire. (except for primary charging assembly)

10) Mount the shielding plate (left, right).

For other charging assemblies, fit the lid (2 pc.).

After stringing the charging wire of each charg-
ing assembly, check to make sure that the length
of the tension spring is as follows:

F-7-137

[2]

[1]

[1]

Stud

Reel

Charging wire

Charging
terminal

(front)

(rear)

Grid side

(correct)

(wrong)

A

Primary
charging
assembly

Pre-transfer
charging
assembly

Transfer
charging
assembly

Separation
charging
assembly

A=12.0±1mm

A=12.0±1mm

A=12.0±0.5mm

A=12.0±0.5mm

«
...
227
228
229
230
231
...
»

Summary of Contents for IMAGERUNNER 7095 PRINTER








































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IMAGERUNNER 7095 PRINTER

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: CAB Pages: 40

WorkCentre Pro 421

Brand: Xerox Pages: 4

WorkCentre Pro 412

Brand: Xerox Pages: 212

WORKCENTRE PE 220

Brand: Xerox Pages: 8

WORKCENTRE PE 220

Brand: Xerox Pages: 2

WORKCENTRE PE 220

Brand: Xerox Pages: 200

WorkCentre m940

Brand: Xerox Pages: 86

Brand: Xerox Pages: 24

WorkCentre PE16

Brand: Xerox Pages: 201

WorkCentre M24 Color

Brand: Xerox Pages: 441

WORKCENTRE C2424

Brand: Xerox Pages: 2

WorkCentre M118

Brand: Xerox Pages: 5

WORKCENTRE C2424

Brand: Xerox Pages: 16

WORKCENTRE C2424

Brand: Xerox Pages: 20

WORKCENTRE C2424

Brand: Xerox Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands