Canon IMAGERUNNER 7095 PRINTER Service Manual Download | Manualshive

Page: 271 / 615

background image

Chapter 8

8-38

4) Release the lever [1] in upward direction; then,

slide out the pull-off roller unit [2], and remove
the 2 screws [3].

F-8-75

5) Remove the pull-off roller unit [1] in the

direction of the arrow.

F-8-76

8.11.9 Manual Pickup Roller

8.11.9.1 Removing the Pickup Roller

0010-8992

1) Open the manual tray paper guide.
2) Remove the left/right stop rings [1] (two each),

shutters [2] (two each), spacers [3] (two each),
and rolls [4] (two each).

F-8-77

If the multifeeder is used during installation or if
the multifeeder has not been used for a long time,
pickup can fail. If such happens, detach the pro-
tective sheet from the sponge roller, and dry wipe
the sponge roller.

8.11.9.2 Mounting the Pickup Roller

0010-8993

Mount the pickup roller by reversing the steps
used to remove it with the following in mind:
- The front pickup roller and the rear pickup roller

are not interchangeable.

- The front pickup roller is identified by its silver-

colored collar.
When mounting the pickup roller [1] to the
pickup assembly, be sure that the round
marking [2] on the collar (silver) is toward the
machine's front,

F-8-78

- The rear pickup roller is identified by its gold

collar.
When mounting the pickup roller [3] to the
pickup assembly, be sure that the round
marking [4] on the side of the roller and the
round marking [5] on its collar (gold) are
toward the machine's rear.

F-8-79

8.11.10 Manual Feed Roller

8.11.10.1 Removing the Feeding Roller

0010-8994

1) Remove the pickup roller, and remove the stop

ring.

2) Remove the two screws [1], and detach the

manual feed tray guide [2].

F-8-80

[3]

[1]

[2]

[1]

[1] [2]

[3]

[4]

[4]

[3]

[2]

[1]

[1]

[2]

Direction of
rotation

Collar (silver)

front of
the machine

Direction of
rotation

Collar (gold)

[3]

[4]

[5]

rear of
the machine

[1]

[2]

[1]

«
...
269
270
271
272
273
...
»

Summary of Contents for IMAGERUNNER 7095 PRINTER








































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IMAGERUNNER 7095 PRINTER

Brand: Lanier Pages: 3

Brand: TASKalfa Pages: 36

Brand: Ricoh Pages: 4

TELEIOS GRANDE G5

Brand: d.gen Pages: 14

LaserPro StellarMark IFII Series

Brand: GCC Technologies Pages: 111

ECOSYS FS-6530MFP

Brand: Kyocera Pages: 2

Brand: SATO Pages: 255

Brand: Tally Pages: 14

Brand: Xerox Pages: 48

Brand: Olivetti Pages: 97

2020D - Aficio B/W Laser

Brand: Ricoh Pages: 116

Designer XL PRO

Brand: PICASO 3D Pages: 72

Brand: IBM Pages: 128

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands