manualshive.com logo in svg

Canon IMAGERUNNER 7095 PRINTER, Service Manual

The Canon imageRUNNER 7095 Printer delivers unparalleled performance with its impressive specifications. For easy accessibility, users can download the user manual for this printer free of charge from 88.208.23.73:8080. Explore the comprehensive manual to optimize the functionality of this exceptional printer.

Share
Download
background image

Chapter 16  

16-22

16.3.3 Jam Code (DADF-M1)

0011-5509

<iR7086>

T-16-7

0085

error

PI1,PI2,PI
11

A motor error other than an IPC communication or pickup error has 
occurred. (less than 3 times)

0090

ADF open

PI10

The ADF is identified as being open.

0091

user DF open

PI10

The ADF is identified as being open while the machine is operating.

0092

cover open

PI3,PI6

The cover is identified as being open.

0093

user cover open

PI3,PI6

The cover (front or rear) is identified as being open while the machine is 
operating.

0094

initial stationary

PI4,PI12,P
I13,S1,S2,
S3,S4,S5,S
9

At the start of operation, a sensor inside the paper path detects an original.

0095

cycle fault

S6

The pickup signal has been received for a specific period of time (2 sec) 
in the absence of a detected original.

0096

residual original

S1

The reversal sensor detects an original while the belt motor is moved for 
a specific distance before the start of a left pickup job.

0097

manual feeder 
residual original

S1,S9

At time of manual feed pickup, the reversal sensor detects an original 
while the manual feeder registration roller sensor also detects an original.

0098

power-down

-

A drop occurs in the voltage supplied by the host machine while the 
machine is operating.

Code

Sensor

Notation

Description

0001

post-separation sensor

PI7

The post-separation sensor does not detect paper when paper 
has been moved 452 mm after the start of separation.

0002

post-separation sensor

PI7

- The separation sensor detects paper when paper has been 
moved 500 mm (if extra-length, +200 mm) -45.5 mm after 
registration pickup.
- the sensor goes on (paper with hole) before paper has been 
fed 12 mm after the detection of the trailing edge; the 
separation sensor detects paper after paper has been fed 50 
mm from when the separation senor has gone on.

0003

registration sensor

PI1

The registration sensor does not detect paper a feed length of 
134.8 mm after the post-separation sensor has gone on.

0004

registration sensor

PI1

The read sensor goes off before the registration sensor goes 
off.

0005

read sensor

PI8

- The read sensor does not detect paper a feed length of 364.2 
mm (182.1 x 2) from the point of registration.
- The read sensor does not detect paper a feed length of 157.4 
mm (78.7 x 2) from the point of No. 2 registration.

0006

read sensor

PI8

- The read sensor detects paper a feed length of 500 mm (if 
extra-length, +200 mm) after the start of feed, resumed after 
a temporary stop for reading.
- At time of LTRR/LGL identification in mix mode, the read 
sensor detects paper a feed length of 514 mm after the start of 
feed from the edging wait point.

0007

delivery reversal sensor

PI9

If not in high-speed duplexing mode, the delivery sensor does 
not detect paper when paper is moved 132.1 mm after it has 
reached the leading edge lower stream roller with reference to 
the activation of the read sensor.

0008

delivery reversal sensor

PI9

The delivery sensor detects paper a feed length of 161.9 mm 
after the trailing edge read end point.

0042

post-separation sensor

PI7

1st sheet, post-separation sensor, stationary

0043

registration sensor

PI1

1st sheet, registration sensor, non arrival

Code Sensor type

Sensor No. Description

Summary of Contents for IMAGERUNNER 7095 PRINTER








































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IMAGERUNNER 7095 PRINTER

Oki 6150 Setup Manual preview
6150
Brand: Oki Pages: 40
3D Systems CubePro Setup And Repacking Manual preview
CubePro
Brand: 3D Systems Pages: 26
3D Systems CubePro Repair Manual preview
CubePro
Brand: 3D Systems Pages: 39
3D Platform WorkSeries 200 Series Quick Reference Manual preview
WorkSeries 200 Series
Brand: 3D Platform Pages: 9
Datecs PP-55 User Manual preview
PP-55
Brand: Datecs Pages: 73
Datamax H-Class Quick Start Manual preview
H-Class
Brand: Datamax Pages: 12
Datamax E-Class Mark II Maintenance Manual preview
E-Class Mark II
Brand: Datamax Pages: 40
Datamax E-class E-3202 Quick Reference Manual preview
E-class E-3202
Brand: Datamax Pages: 46
Xerox Phaser 5335 Installation Manual preview
Phaser 5335
Brand: Xerox Pages: 2
Savin C2410 Reference Manual preview
C2410
Brand: Savin Pages: 160
Muratec MFX-3550 User Manual preview
MFX-3550
Brand: Muratec Pages: 213
Patton electronics PeNet 2127 User Manual preview
PeNet 2127
Brand: Patton electronics Pages: 16
Sam4s giant 100 series User Manual preview
giant 100 series
Brand: Sam4s Pages: 54
Plas-Ties A401870 Series Manual preview
A401870 Series
Brand: Plas-Ties Pages: 18
FujiFilm Digital Minilab Frontier LP5700R Brochure & Specs preview
Digital Minilab Frontier LP5700R
Brand: FujiFilm Pages: 2
Zonet ZPS3611 - QUICK Quick Installation Manual preview
ZPS3611 - QUICK
Brand: Zonet Pages: 1
Epson ET-4500 User Manual preview
ET-4500
Brand: Epson Pages: 277
Epson ET-4550 User Manual preview
ET-4550
Brand: Epson Pages: 288

Brands by name

Popular brands

Load more brands