43-0073
-
Drum Unit replacement completion alarm
A. Operation / B. Cause /
C. Remedy
The replacement of the Drum Unit was detected.
50-0010
-
Successive occurrence of separation alarm
A. Operation / B. Cause /
C. Remedy
Condition unable to separate 1st sheet of original from the ADF occurs 3 times in a row. Check
rotation of the Pickup Motor -> Check the life of the Pickup Roller -> Check if paper lint is at the
pickup slot.
50-0014
-
Insufficient Scanner Unit (Paper Back) LED light intensity alarm (Some of the LEDs are OFF.
Scanning can be continued.)
A. Operation / B. Cause /
C. Remedy
In the case that the light intensity is insufficient at LED lighting.
50-0015
-
ADF Double Feed Detection Senser trouble
A. Operation / B. Cause /
C. Remedy
60-0001
-
Shift Tray alarm
A. Operation / B. Cause /
C. Remedy
Movement: Shift Tray operation is stopped.
Cause: Home position at startup of the host machine cannot be detected.
Measure: Check connector disconnection of the HP Sensor (Front) (PS101) and the HP Sensor
(Rear) (PS102) -> Replace the HP Sensor (Front) (PS101) and the HP Sensor (Rear) (PS102).
61-0002
-
Finisher Staple Free Stapling alarm: Fin-J1/Y1
A. Operation / B. Cause /
C. Remedy
Cause: The staple free staple unit is broken.
Operation : Operation stops as jam. After jam processing, the paper is delivered without stapling
until a job is finished.
Recovery method : Replace the Staple free staple unit. After performing the remedy work, go
through the following to clear the alarm: SORTER> FUNCTION> EMSG-CLR.
70-0086
-
For R&D
A. Operation / B. Cause /
C. Remedy
70-0087
-
Firmware combination mismatch
A. Operation / B. Cause /
C. Remedy
Cause: An option with the firmware which version is newer than that of the firmware installed in
the host machine was detected. It is an alarm when the automatic update cancellation message
is displayed on the Control Panel.
Detection condition:
When the following two conditions are satisfied:
1. "1" is set in COPIER>Option>FNC-SW>VER-CHNG.
2. The version of the firmware installed in the option that has been installed to the host machine
is newer than that of the firmware in the host machine.
Timing: At startup
Movement/symptom: Cancel the automatic update.
Measures: Update the firmware of the host machine.
73-0006
-
LIPS
A. Operation / B. Cause /
C. Remedy
Error in configuration acquisition/management
73-0007
-
For R&D
A. Operation / B. Cause /
C. Remedy
-
73-0008
-
For R&D
A. Operation / B. Cause /
C. Remedy
-
7. Error/Jam/Alarm
527
Summary of Contents for imagerunner advance 4551i
