Address
bit
Name
Circuit code
Remarks
5
-
-
-
4
-
-
-
3
-
-
-
2
OPEN Detection Sensor
PS403
L: OPEN
1
Buffer Pass Exit Sensor
PS402
L: Paper
0
Buffer Pass Inlet Sensor
PS401
L: Paper
ADJUST
■ AE
COPIER > ADJUST > AE
AE-TBL
1
Adj of text density at image density adj
Detail
To adjust text density according to the adjusted image density.
As the greater value is set, text gets darker.
Use Case
When clearing the RAM data of the Reader Controller PCB
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
When clearing the RAM data of the Reader Controller PCB, enter the value of service label.
Display/Adj/Set Range
1 to 9
Default Value
5
■ ADJ-XY
COPIER > ADJUST > ADJ-XY
ADJ-X
1
Adj start pstn in book mode: vert scan
Detail
To adjust the image reading start position (image leading edge position) in the vertical scanning
direction at copyboard reading.
When replacing the Reader Controller PCB/clearing RAM data, enter the value of service label.
Decrease the value when the non-image width is larger than the standard value.
Increase the value when out of original area is copied.
As the value is incremented by 1, the image position is moved to the trailing edge side by 0.1 mm.
Use Case
When replacing the Reader Controller PCB/clearing RAM data
Adj/Set/Operate Method
1) Enter the setting value (switch negative/positive by -/+ key) and press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
-50 to 50
Unit
mm
Default Value
0
Amount of Change per
Unit
0.1
8. Service Mode
640
Summary of Contents for imagerunner advance 4551i
