COPIER > ADJUST > MISC
ACS-EN3
2
ACS mode judgmt area:stream, bck, 1-path
Detail
To set the ACS judgment area in the image on the back side stream read with the DADF (1-path
model).
As the value is larger, the judgment area is widened.
The setting of this item is enabled only when the DADF (1-path model) is installed.
Use Case
When adjusting the ACS judgment area in the image on the back side at stream reading
Adj/Set/Operate Method
1) Enter the setting value (switch negative/positive by -/+ key) and press OK key.
2) Turn OFF/ON the main power switch.
Caution
When the Copyboard or DADF (reverse model) is installed, the setting of this item is disabled.
Display/Adj/Set Range
-2 to 2
Default Value
1
ACS-CNT3
2
Chromatic clr jdgmt area:strem,bck,1path
Detail
To set the area to judge whether the image on the back side stream read with DADF (1-path model)
is color or B&W at automatic color selection.
As the value is larger, the judgment area is widened.
The setting of this item is enabled only when the DADF (1-path model) is installed.
Use Case
When adjusting the area where the pixel is counted to judge whether it is a color/B&W image
Adj/Set/Operate Method
1) Enter the setting value (switch negative/positive by -/+ key) and press OK key.
2) Turn OFF/ON the main power switch.
Caution
When the Copyboard or DADF (reverse model) is installed, the setting of this item is disabled.
Display/Adj/Set Range
-2 to 2
Default Value
0
FUNCTION
■ INSTALL
COPIER > FUNCTION > INSTALL
TONER-S
1
Toner supply to Developing Assembly
Detail
To execute a series of operation necessary for supplying toner to the Developing Assembly/Toner
Supply area (drive the Developing Cylinder, Toner Stirring/Feed Member) as a whole.
After counting down from 600 seconds, it is stopped automatically.
Use Case
- At installation
- When replacing the Developing Assembly
- When replacing toner in the Developing Assembly
Adj/Set/Operate Method
1) Select the items.
"Check the Developer" is displayed.
2) Check connection, and then press OK key.
It automatically stops after 10 minutes.
Caution
- Although "Check the Developer" is displayed when selecting the item, be sure to check the
connection between the Developing Assembly and connector.
- The operation can stop manually with OK key when a failure occurs.
Display/Adj/Set Range
During operation: xxx second (remaining time), When operation finished normally: OK!
Default Value
600
8. Service Mode
689
Summary of Contents for imagerunner advance 4551i
