![background image](http://html1.mh-extra.com/html/canon/imagerunner-advance-4551i/imagerunner-advance-4551i_service-manual_4280156709.webp)
COPIER > FUNCTION > CST
MF-A6R
1
Reg Multi-purpose Tray A6R stdrd width
Detail
To register the standard value of A6R paper width (105 mm) on the Multi-purpose Tray.
Make a fine adjustment by COPIER> ADJUST> CST-ADJ> MF-A6R.
Adj/Set/Operate Method
1) Set A6R paper on the Multi-purpose Tray, and set the guide so that it fits the paper width.
2) Select the item, and then press OK key.
The value is registered after automatic adjustment.
Caution
After execution, check the registered value by COPIER> ADJUST> CST-ADJ> MF-A6R, and write
it down on the service label.
Related Service Mode
COPIER> ADJUST> CST-ADJ> MF-A6R
MF-A4
1
Reg Multi-purpose Tray A4 standard width
Detail
To register the standard value of A4 paper width (297 mm) on the Multi-purpose Tray.
Make a fine adjustment by COPIER> ADJUST> CST-ADJ> MF-A4.
Adj/Set/Operate Method
1) Set A4 paper on the Multi-purpose Tray, and set the guide so that it fits the paper width.
2) Select the item, and then press OK key.
The value is registered after automatic adjustment.
Caution
After execution, check the registered value by COPIER> ADJUST> CST-ADJ> MF-A4, and write
it down on the service label.
Related Service Mode
COPIER> ADJUST> CST-ADJ> MF-A4
DK1-INT1
1
Initialization at Deck parts replacement
Detail
To execute initialization of Paper Deck at parts replacement.
By executing this item, the lifter moves up from the lower limit position and stops when the Paper
Surface Sensor detects paper top face. The travel distance is reflected to the paper level detection
control."
Use Case
When replacing the Pickup Unit/PCB/compartment
Adj/Set/Operate Method
Select the item, and then press OK key.
Caution
Execute this item while there is no paper in a deck and the lifter is in stopped state.
Display/Adj/Set Range
During operation: ACTIVE, When operation finished normally: OK!
Required Time
30 sec
DK1-SPAD
1
Setting of Deck Lifter stop position
Detail
To set stop position of the lifter when opening the compartment of the Paper Deck Unit.
When 0 is set, the lifter moves down to the lower limit position when the compartment is opened.
When 1 is set, the lifer moves up to the pickup position and then the compartment opens. The
height of the Pre-separation Plate can be adjusted.
Even 1 is set, the value is returned to 0 when the compartment is opened.
Use Case
When adjusting pre-separation position after replacing the Pickup Unit/compartment
Adj/Set/Operate Method
Enter the setting value, and then press OK key.
Caution
Even 1 is set, the value is returned to 0 when the compartment is opened.
Display/Adj/Set Range
0 to 1
0: Stop at lower limit position (normal), 1: Stop at pickup position
Default Value
0
DK1-LIFT
1
Drive of Deck Lifter Motor
Detail
To drive the Lifter Motor of the Paper Deck.
When descent timeout alarm (04-1537) occurs, the lifter wire may be wound in the opposite
direction. The Lifter Motor is driven for approximately 5 seconds to wind the wire correctly.
Use Case
At recovery from descent timeout alarm
Adj/Set/Operate Method
1) Close the compartment.
2) Select the item, and then press OK key.
Display/Adj/Set Range
During operation: ACTIVE, When operation finished normally: OK!
8. Service Mode
696
Summary of Contents for imagerunner advance 4551i
