COPIER > OPTION > FNC-SW
SVMD-ENT
2
Setting of entry method to service mode
Detail
To set the way to get in service mode to prevent information leak.
Use Case
As needed
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
0 to 1
0: Factory default
1: [Settings/Registration] - Pressing [4] and [9] at the same time - [Settings/Registration]
Default Value
0
KSIZE-SW
2
Set of Chinese paper (K-size) support
Detail
To set to detect/display the Chinese paper (K size paper: 8K, 16K).
Use Case
When using K size paper
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
Go through the following: COPIER> OPTION> FNC-SW> MODEL-SZ; and if MODEL-SZ is "0: AB
configuration", this mode is enabled.
Display/Adj/Set Range
0 to 1
0: Not supported, 1: Supported
Default Value
It differs according to the location.
Related Service Mode
COPIER> OPTION> FNC-SW> MODEL-SZ
Supplement/Memo
8K paper: 270 x 390 mm, 16K paper: 270 x 195 mm
ORG-B4
2
Special ppr size set at stream read: B4
Detail
To set the size of special paper (B4 configuration) that cannot be recognized in stream reading
mode.
Use Case
- Upon user's request
- When picking up special paper size original from DADF
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
0 to 1
0: B4R, 1: FOLIO-R
Default Value
0
PDF-RDCT
2
PDF reduction set at forwarding
Detail
To set whether to reduce the image for transmission when converting the image received by IFAX
into PDF for e-mail/file transmission.
Use Case
Upon user's request
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
0 to 1
0: Following the current setting, 1: Image reduction
Default Value
0
SJB-UNW
2
Reserve upper limit of secured print job
Detail
*Operation on this item is restricted by the setting of [Restrict Service Representation Access].
To set the upper limit for the number of reserved jobs in secured print job.
Use Case
Upon user's request
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
0 to 2
0: 50 jobs, 1: 90 jobs, 2: No limit
Default Value
1
8. Service Mode
719
Summary of Contents for imagerunner advance 4551i
