■ MG-TR
COPIER > OPTION > MG-TR
HUM-SW
2
Switching of environmental fixed mode
Detail
The transfer current is output according to the setting.
- Low humidity environment: The transfer current output becomes higher.
- High humidity environment: The transfer current output becomes lower.
Use Case
Use this item when a failure occurs to the environment sensor. The output level of transfer current
is controlled in accordance with the specified environment.
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
0: Automatic control by the environment sensor
1, 2: N/L (temperature: 23 deg C, humidity: 5 %)
3, 4: N/N (temperature: 23 deg C, humidity: 50 %)
5: H/H (temperature: 30 deg C, humidity: 80 %)
Make the setting in accordance with the installation environment.
The transfer current output level is controlled in accordance with the specified environment.
Default Value
0
TROPT-SW
2
Adj of transfer output
Detail
To adjust the transfer roller voltage
Use Case
- When the moist paper or recycled paper is used so that the transfer failure occurs, decrease the
transfer output.
- When the thick paper is used so that the transfer failure occurs, increase the transfer output.
Adj/Set/Operate Method
Enter the setting value, and then press OK key.
Display/Adj/Set Range
-1 to 1
-1: Transfer output voltage decreases.
0: OFF
1: Transfer output voltage increases.
Default Value
0
TR-BS-SW
2
Set transfer bias highland ev mode
Detail
To control the transfer bias in printing so that it does not exceed a specified level
Use Case
When the black spots appear on the image (caused by leak occurs at high latitude)
Adj/Set/Operate Method
Enter the setting value, and then press OK key.
Caution
When the installation site is changed from a highland to a lowland, set this mode OFF.
Display/Adj/Set Range
0 to 1
0: Normal, 1: Voltage reduction mode
Default Value
0
■ IMG-FIX
COPIER > OPTION > IMG-FIX
FIX-CLN
2
Set fixing cln sequence execution temp
Detail
To set the execution temperature for the fixing pressure roller cleaning sequence
Change the condition (temperature deference between the main thermistor and the sub thermistor)
to execute the fixing pressure roller cleaning sequence. When the input value is increased, the
execution period is extended.
Use Case
When an image failure due to the Pressure Roller occurs
Adj/Set/Operate Method
Enter the setting value, and then press OK key.
Caution
As the short execution interval is set, productivity decreases.
Display/Adj/Set Range
0 to 3
0: 35 deg C, 1: 40 deg C, 2: 45 deg C, 3: 50 deg C
Default Value
0
8. Service Mode
757
Summary of Contents for imagerunner advance 4551i
