■ P-STOP
COPIER > TEST > P-STOP
PRINTER
1
Forcible stop of paper feed
Detail
To forcibly stop paper for the next job at the specified position (only once).
Leading edge of paper stops at the specified position so that the cause of a problem can be
identified.
When the operation is stopped forcibly, jam code "AAxx" is displayed.
Use Case
- When bent paper/skew/wrinkles occur
- When jam occurs frequently
Adj/Set/Operate Method
1) Enter the setting value, and then press OK key.
2) Execute a job (copy/test print).
Paper stops at the specified position.
Caution
- Remove the paper being stopped with the normal jam removal procedure. After jam removal, the
job is automatically recovered.
- Display of standard jam code indicates that a jam occurs somewhere other than the specified
position. Setting of forcible stop is enabled until paper stops at the specified position.
- The setting is disabled for job where paper does not pass through the specified position.
- Unfixed toner may be adhered on paper depending on the stop position. Thus, handle it with
care.
Display/Adj/Set Range
0 to 255
0: OFF
1: Outlet of the Vertical Path Slave Roller (cassette 1)
2: Outlet of the Vertical Path Slave Roller (cassette 2)
3: Outlet of the Vertical Path Slave Roller (cassette 3)*3
4: Outlet of the Vertical Path Slave Roller (cassette 4)
5: Outlet of the Deck Pull-out Roller
6: Inlet of the Registration Roller
7: Inlet of the Registration Roller (2nd side)
20: Registration Roller
21: Registration Roller (2nd side)
30: Inlet of the Fixing Assembly
31: Inlet of the Fixing Assembly (2nd side)
32: Outlet of the Fixing Assembly
33: Outlet of the Fixing Assembly (2nd side)
40: Outlet of the First Delivery *1
41: Outlet of the First Delivery (2nd side) *1
42: Outlet of the Vertical Path Slave Roller *1
43: Outlet of the Vertical Path Slave Roller (2nd side) *1
50: Outlet of the Second Delivery *1
51: Outlet of the Second Delivery (2nd side) *1
70: Reverse Mouth *2
71: Inlet of the Duplex Inlet Roller *2
72: Outlet of the Duplex Inlet Roller *2
73: Outlet of the Duplex/Feeding Roller *2
99: Inlet of the Fixing Assembly (for checking image)
Any value other than those mentioned above: Not used
*1: Paper may not be stopped depending on the delivery destination setting.
*2: Paper is stopped after being reversed for a 2-sided job.
*3: The paper stop in the same position on the High Capacity Cassette Feeding Unit installation.
Default Value
0
8. Service Mode
822
Summary of Contents for imagerunner advance 4551i
