FUNCTION
SORTER > FUNCTION
FN-SENS1
1
Adj Punch Horz Rgst Sensor: Fin-J1/Y1
Detail
To automatically adjust the output of the Horizontal Registration Sensor 1 to 5 of the Puncher Unit
in sequence.
Horizontal Registration Sensor 1: A3/A4, 2: LDR/LTR, 3: B4/B5, 4: A4R/LTRR/LGL, 5: B5R
Use Case
- When installing/replacing the Puncher Unit
- When replacing the Horizontal Registration Sensor of the Puncher Unit
Adj/Set/Operate Method
Select the item, and then press OK key.
Caution
When the sheet of paper is on the sensor, the adjustment fails.
Display/Adj/Set Range
During operation: ACTIVE, At normal termination: OK, At abnormal termination: NG
FN-SENS2
1
Adj Punch Waste Full Sensor: Fin-J1/Y1
Detail
To automatically adjust the output of Punch Waste Full Sensor (Punch Waste Full Detection PCB)
of the Puncher Unit.
Use Case
- When installing/replacing the Puncher Unit
- When replacing the Punch Waste Full Sensor
Adj/Set/Operate Method
Select the item, and then press OK key.
Caution
When the sheet of paper is on the sensor, the adjustment fails.
Display/Adj/Set Range
During operation: ACTIVE, At normal termination: OK, At abnormal termination: NG
FIN-BK-R
1
Backup data saving: Fin-J1/V1
Detail
The backup data is read from the finisher controller PCB and saved to HDD.
Use Case
When replacing the Finisher Controller PCB
Adj/Set/Operate Method
1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
During operation: ACTIVE, At normal termination: OK, At abnormal termination: NG
Related Service Mode
SORTER> FUNCTION> FIN-BK-W
FIN-BK-W
1
Backup data writing: Fin-J1/Y1
Detail
The backup data saved in HDD is written to the finisher controller PCB.
Use Case
When replacing the Finisher Controller PCB
Adj/Set/Operate Method
1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/Adj/Set Range
During operation: ACTIVE, At normal termination: OK, At abnormal termination: NG
Related Service Mode
SORTER> FUNCTION> FIN-BK-R
FIN-CON
1
FIN-Controller PCB RAM clear:Fin-J1/Y1
Detail
To execute the RAM clear of Finisher Controller PCB to delete all the adjustment contents. (except
the counter information)
Use Case
When clearing RAM data of the Finisher Controller PCB
Adj/Set/Operate Method
1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
- Output the service mode setting values by P-PRINT before execution. After execution, enter the
necessary setting values.
- RAM clear is executed after the main power is turned OFF/ON.
Display/Adj/Set Range
During operation: ACTIVE, At normal termination: OK, At abnormal termination: NG
Related Service Mode
COPIER> FUNCTION> MISC-P> P-PRINT
Supplement/Memo
The adjustment values stored to the puncher controller PCB does not cleared.
8. Service Mode
864
Summary of Contents for imagerunner advance 4551i
