Setting the Host Machine
■ Starting the Setup Guide
CAUTION:
• The Setup Guide screen appears when the power
is turned ON for the first time after the machine is
installed. Follow the instructions displayed on the
Touch Panel Display to configure the settings of
the host machine.
• It is not possible to exit Setup Guide halfway
through.
• Setup Guide can be started again from [Settings/
Registration] ( [Settings/Registration] >
[Management Settings] > [License/Other] > [Start
Setup Guide]).
• What has been registered in Setup Guide can be
changed from items in (Settings/Registration).
When configuring settings using Setup Guide,
excluding some of the setting items, it is possible
to proceed to the next setting without entering the
current setting. To configure skipped settings,
configure the settings one by one after exiting
Setup Guide. If the host machine is turned OFF
during registration using Setup Guide, Setup
Guide is automatically started by turning ON the
power again. Once registration using Setup Guide
has been completed, Setup Guide is not
automatically started by turning ON the host
machine.
CAUTION:
Register the information of paper loaded during
installation of the host machine.
Be sure to register the correct paper type. Especially in
the case of special paper types such as heavy paper,
registering a wrong paper type may result in image
failure, and when the Fixing Assembly becomes soiled
or paper wraparound occurs, repair by a service
technician becomes necessary.
When Setup Guide is not executed, it can be canceled by
pressing [Cancel] on the Touch Panel Display. When
Setup Guide is executed, follow the Setup Guide to
specify the items in the order shown below:
1. <Switch Language/Keyboard>
Select the displayed language and keyboard layout.
2. <Toner Mixing>
Press [Start] to mix the toner (approx.10 minutes). While
mixing, install the Tray, set the Cassette and perform
other Installations.
3. <Paper Settings>
1. Select the paper source for which you want to
specify the paper type, and press [Set].
2. Select the paper type, and press [OK].
3. If [Plain] is selected, the basis weight can be specify
from [Plain Paper Weight Set].
4. If a button corresponding to the paper that has been
set is not displayed, press [Detailed Settings] and
make a selection on the detailed settings screen.
NOTE:
• If the corresponding paper type is not displayed on
the simple settings screen, press [Detailed Settings]
and make a selection on the detailed settings screen.
• If the type of loaded paper is not displayed on the
detailed settings screen, you can register it.
4. <Authentication Login>
NOTE:
Pressing [Skip] proceeds to auto gradation adjustment
instead of the setting of system administrator privilege.
Press [Log in], and enter a password.
CAUTION:
• Do not change Administrator here.
• Enter the initial value "7654321" in the password
entry field.
5. <Use Optional Output Tray>
Set whether to use the optional output tray.
CAUTION:
Make sure the output tray that is set to On is attached
to the device, or the output tray will not function
correctly.
6. <Date/Time Settings>
Set the date and time.
CAUTION:
Perform the network settings according to the user's
request.
7. <Use IP Address>
Specify IPv4 and/or IPv6, and each IP address.
8. <DNS Server Address Settings>
Configure the DNS Server Address Settings, the DNS
Host/Domain Name Settings, and the DNS Dynamic
Update Settings.
9. <Proxy Settings>
Specify the Proxy Settings.
10. <Country/Region> (FAX-TYPE settings)
Select Country/Region.
9. Installation
894
Summary of Contents for imagerunner advance 4551i
