[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
■ Power Supply Assembly
An overview of the power supply is indicated below.
With this equipment, 4 types of power (24 V, 12 V, 6 V, and 5 V) are received from the Reader Unit.
The 24 V power is mainly used for the motor, solenoid, fan.
The 12 V power is mainly used for the LED Lamp Unit.
The 5 V power is mostly used for the sensors.
3.3 V power is generated via a converter on the ADF Driver PCB and supplied to the Original Width Volume.
24V
24V
6V
4.5V
3.3V
24V
24V
Reader
controller
PCB
Solenoid
Motor
Fan
5V
Sensor
24V
DADF driver
PCB
Scanner Unit
PCB
LED
lamp unit
Original
width volume
24V
5V
Related Error Code
Power supply (24 V) error
• E227-0101: 24 V port is OFF when the power of the DF Unit is turned ON
ADF_Reversal ADF
■ Basic Operation
● Outline
The ADF has the following operation modes.
Operation mode name
Outline of operation
Associated print mode
Forward pickup/Delivery Picks up, reads, and then delivers a document.
Single-sided document -> Simplex printing
Single-sided document -> Duplex printing
Forward feed/Reverse
delivery
Picks up, reads, reverses, and delivers a document.
Double-sided document -> Duplex printing
Double-sided document -> Simplex printing
2. Technology
63
Summary of Contents for imagerunner advance 4551i
