No
Items
Outline
Use case
[6] Lv.1) SORTER> OPTION> MSTP-WT
To set the duration of time to keep man-
ual staple mode enabled after execution
of manual stapling.
Upon user's request
[7] Lv.1) SORTER> OPTION> TRY-PSTN
To set the tray position after the comple-
tion of job
Upon user's request (to improve visibility
of the delivered papers)
[8] Lv.1) SORTER> OPTION> PUCH-SW
Switching the high-productivity punch
mode or high-accuracy punch mode of
the inner puncher unit
• When switching the high-productiv-
ity punch mode or high-accuracy
punch mode.
• This mode is available when the in-
ner puncher unit has been installed.
[9] Lv.1) SORTER> OPTION> PUN-Y-SW
To set whether to perform the horizontal
registration operation of the inner punch-
er unit for matching with the center of the
paper
• When the adjustable range of the
punch hole horizontal registration
adjustment is enlarged.
• This mode is available when the in-
ner puncher unit has been installed.
[10] Lv.1) SORTER> OPTION> PNCH-SW2
To set the punch hole specification of the
inner puncher unit
• When replacing the Puncher Con-
troller PCB.
• This mode is available when the in-
ner puncher unit has been installed.
SORTER > OPTION
FIN-SP1
Finisher special setting 1 (To set jogging amount of the alignment plate for stack delivery oper-
ation)
Lv.2
Details
To perform the finisher special setting 1
FIN-SP1 consists of bit switches 0 through 7.
Bit-0 (right end) is assigned for setting jogging amount of the alignment plate in stack delivery
operation. When setting the bit-0 to "1", the jogging amount changes in the stack delivery mode
with the following configuration so that the alignment plate does not press a paper stack:
- Configuration: Small size(*1), plain1/recycled1, 1-sided, Shift-sort/Non-sort
Setting of the bit-0:
When setting to "0", the special setting 1 is OFF. (The rear alignment plate presses a paper stack
by 1mm.)
When setting to "1", the special setting 1 is ON. (The rear alignment plate withdraws from a paper
stack by 0.5mm.)
Use case
When E514 (Assist error) appears in the stack delivery mode with the following configuration:
- Configuration: Small size(*1), plain1/recycled1, 1-sided, Shift-sort/Non-sort
Adj/set/operate method
Press bit-0 to switch the value and press "OK".
Caution
Setting the bit-0 to "1" may cause a poor alignment of paper stack in the feeding direction.
Bit-1 through 7 are reserved. Their numeric parameters on the display can be changed for nothing.
Display/adj/set range
00000000 to 11111111
Default value
00000000
*1: Small size (feed length: 216 mm or less)
A4, A5, A5R, B5, LTR, STMT, STMT-R, 16K, EXEC
Adjustment Items When Replacing Parts
No
Target part
Adjustment item and description
Reference
1
Finisher Controller PCB
Backup operation before replacement and operation after re-
placement
“Handling Finisher Controller
PCB Replacements” on page
75
5. Adjustment
74
Summary of Contents for Inner Finisher-J1
