Canon iPF8400S Series Service Manual Download

Page: 281 / 312

Chapter 8

8-5

1048

GL2: W0904
The memory is full.

GL2: W0903

HP/GL2 error; polygon buffer overflow
The size of drawing data exceeds the
processing capacity.

1. Reduce the size of rendering data.
2. Replace with HP RTL data for
manipulation with On The Fly*.

*: On The Fly: The method to transmit
data in sequence from paper. The
software that generates HP-GL/2 data
has this option to specify. Select this
option to save the memory usage of the
printer.

1049

Before borderless
printing, move the
blue platen switch.

When print data with borderless printing
specification has been received, platen
shutter was closed.

Open the platen shutter.

1050

Blue platen switch
is dirty. Please
clean the switch.

Cleaning of platen shutter is necessary.

When reading the platen shutter in
multisensor, borderless printing data has
been received in unstable output condition.

Clean the platen shutter.

1051

Paper Too Small

Paper mismatch (size)
Size clip warning
With [Warning Indication] selected for
[Paper Mismatch Detection] in the menu
settings, the size of paper loaded is smaller
than that of specified from driver.

Continued printing allowed.
Check driver settings.
Replace with appropriate paper.

1052

Borderless printng
not possible. Check
supported paper.

Borderless printing not available
(unsupported size)

With [Warning Indication] selected for
[Paper Mismatch Detection] in the menu
settings, borderless printing data is
received, but roll paper not supporting
borderless printing has been loaded.

Replace with appropriate paper.

1053

Paper position not
suitable for
borderless printing.

Borderless printing not available (physical)
With [Warning Indication] selected for
[Paper Mismatch Detection] in the menu
settings, borderless printing data is
received, but roll paper loaded is more than
1mm off the predefined position for the
pre-ejection opening at the counter-HP
side.

Reload/ replace the roll paper.

1053

Borderless printng
not possible. Check
pap. pos. or spacer

Reload/ replace the roll paper.
Check the borderless spacer.

1054

PaprWidth Mismatch

Paper mismatch (size)
With [Warning Indication] selected for
[Paper Mismatch Detection] in the menu
settings, the width of roll paper loaded and
that of specified by data do not match.

Continued printing allowed.
Check driver settings.
Replace with appropriate paper.

1056
to
1062

Move the blue
platen switch No.XX
to the right.

The multisensor detected that the platen
shutter used for pre-ejection was closed.
Detection timing:
-At paper loading
-At start of first printing (after upper cover
is opened and closed, or recovery from
sleep mode, or the power is turned on with
paper loaded)

The following list shows the last 2 digits of
error codes and the corresponding
messages.
56:No.2, 57:No.3, 58:No.459:No.5,
5A:No.6, 5B:No.75C:No.8,
5D:No.9, 5E:No.105F:No.11, 60:No.12,
61:No.13, 62:No.14

Move the platen shutter relevant to the
message to the right, to open it.

1100

Prepare for
maint cart
replacement.

MTCart Full Soon

Maintenance cartridge near-full (continued
usage allowed)
Near-full has been detected from the dot
count and the usage period (drying time).

<Maintenance cartridge detection timings>
The presence of a maintenance cartridge is
detected at the following timings:
1. Before printing/during printing (twice
per second)/at the end of printing/ between
pages
2. Before a recovery operation/during a
recovery operation (twice per second)/
before opening of the ink supply valve
3. When the cartridge is removed and
inserted following the occurrence of an
error or warning.

Prepare a maintenance cartridge.

1101

Replace part soon.

Mist Full Soon

Mist count near-full
Waste ink near-full has been detected from
the dot count.

Check the parts counter and replace the
target unit or Refresh Service Kit.
Initialize the parts counter for the
target unit after the replacement.

Code

(last 4 digits)

Panel display

(Large LCD)

Panel display

(Small LCD)