Canon iPF8400S Series Service Manual Download

Page: 300 / 312

Chapter 8

8-24

2E32

Insufficient paper
for job

All of the following conditions have been
met at the start of external printing:
-[ON] has been selected for [Remaining
Roll Paper Detection].
-Among the paper size settings coded in the
print data, the paper length exceeds the
remaining length of roll paper.
-Automatic roll feed to another roll paper
slot which is not the current feeding path,
out of the 2 slots the printer has, is not
available.

Replace the roll paper.

2E33

Roll Paper
(Paper type)
(Paper size)
Load Roll Paper
Stop Printing

Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.

Load roll paper.
1. Select "load a roll" and follow
instruction on the panel.
2. Select "stop printing," or stop
printing by pressing stop button.
3. Release the release lever and load
the paper.

Roll 1(Upper)
(Paper type)
(Paper size)
Press Load/Eject
and load a roll.

Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When paper has not been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an
error of upper roll occurs.

2E34

Roll 2 (Lower)
(Paper type)
(Paper size)
Press Load/Eject
and load a roll.

Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When no paper has been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an
error of upper roll (2E33) occurs.

Load roll paper.

Roll 2 (Lower)
is selected.

Press Load/Eject
and load a roll.

2E35

Roll printing
is selected.

Paper mismatch (roll paper)
No roll paper has been fed when
performing internal printing.

Load roll paper.

Roll printing
is selected.

Press Load/Eject
and load a roll.

2E36

Roll printing
is selected.

Press Load/Eject
and load a roll.

Paper mismatch (roll paper) (lower)
No roll paper was fed when internal
printing with the specified roll paper
(lower) was started.

Load roll paper.

2E37

Roll printing
is selected.

Paper mismatch (roll paper) (Upper)
No roll paper has been fed when a job with
roll paper specification is received.

Load roll paper.
1. Select "load a roll" and follow
instruction on the panel.
2. Select "stop printing," or stop
printing by pressing stop button.
3. Release the release lever and load
the paper. (This step 3 is only for 800/
8000/9000 series.)

Roll 1 (Upper)
is selected.

Press Load/Eject
and load a roll.

Paper mismatch (roll paper)
No roll paper was fed when the job
specified with upper roll paper was
received.

2E38

Roll 2 (Lower)
is selected.

Press Load/Eject
and load a roll.

Paper mismatch (roll paper)(Lower)
No roll paper has been fed when a job with
lower roll paper specification is received.

Load roll paper.

2E39

The Roll 2 (Lower) is
empty.
Lift the release
lever and replace
the roll.

No roll paper available (trailing edge of roll
paper detected)
-Detected that cut sheet sized paper has
been fed at the roll paper feeding slot.
-The trailing edge of paper was detected by
the Paper detection sensor/ Media sensor
sensor during operation in which roll paper
was used.
-The spool stopped rotating during paper
loading or printing
(XX: Upper roll paper/ Lower roll paper)

1. Replace the roll paper
-Check paper sensor R (I/O mode).
2. Is the paper fed successfully (under
a negative load or any other
influence)?

The roll (XX) is empty.
Press OK.

2E3A

Roll1 jammed. Manually
rewind the
roll all the way
and press OK.

During upper roll paper feeding operation,
the paper was fed with the roll feed sensor
detecting the paper, but the paper detection
sensor/ media sensor sensor could not
detect the paper and the operation timed
out.

Manually rewind the paper and reload.

Roll1 (Uppr) jammed.
Manually rewind the
roll all the way
and press OK.

Code

(last 4 digits)

Panel display

(Large LCD)

Panel display

(Small LCD)

Explanation/Detection sequence

Remedial Action