Canon iR C3380 series Service Manual Download

Page: 546 / 610

Chapter 17

17-62

CNT-DISP

Used to select whether to display serial number when counter check key is pressed.
0: Display serial number.
1: Don't display serial number.

NW-SCAN

Used to select whether to permit network scan function
0: Don't permit
1: Permit (Invalid when UFR board or open interface board isn't connected.)

HDCR-DSP

Selection of clear method in hard disk all data erasure mode
This selects the method clearing the data in the hard disk all data erasure mode.
Settings
1: Cleared once using 0 (null) data.
2: Cleared once using random data.
3: Cleared 3 times using random data.
[Factory setting/value after clearing RAM: 1]

MEMO:

Hard disk all data erasure function
This function overwrites the 0 (null) data and random data in the file data area on the hard disk at the logical timing of
erasing the files (the timing at which the control information data is erased), and it thereby erases all the data on the hard
disk.

JOB-INVL

Used to set job interval during interrupt.
0: Standard setting (Output next job continuously during interrupt copy job.)
1: Start output of next job after last sheet of interrupt copy job has been delivered.
2: Start output of next job after last sheet of any job has been delivered.

P-CRG-LF

Used to select operation performed when drum unit has reached end of service life.
0: Don't stop
1: Stop

PCL-COPY

PCL COPIES command binder control mode
The PCL COPIES command control method differs between the PCLs made in-house and the PCLs made by sources
outside the company, and it is for the purpose of standardizing the operations of both kinds of PCLs that this mode has
been provided.
Settings
0: Control is exercised on a page by page basis as per the COPIES command value specified on the page concerned.
1: The COPIES command value specified on page 1 is treated as the binding number, and the COPIES command values
on the next and subsequent pages are canceled. (This is set only when the sort mode is established. In a non-sorting
mode, the same control is exercised as when "0" is set.)
2 to 65535: Spare
[Factory setting/value after clearing RAM: 0]
"0" is the control method applicable to in-house PCLs, and by setting the item to "1", the same control method as used
with PCLs made by sources outside the company is exercised.

PRJOB-CP

Setting for selecting whether to output the count pulses during reception printing and report printing
This selects whether to output the count pulse notice for each page during reception printing and report printing to the
charge management system when a charge management system (coin vendor or control card made by another company)
is used.
Settings
0: The count pulses are not output.
1: The count pulses are output.
[Factory setting/value after clearing RAM: 0]

DPT-ID-7

Registering a department ID and inputting a 7-digit code for authentication.
Setting Values
0: As before [Factory default/After RAM clear]
1: Inputting a 7-digit code
Reference Infomation Support for Siemens

RUI-RJT

Disconnecting the HTTP port when three authentication failures from RUI are recognized.
Setting Values
0: Invalid [Factory default/After RAM clear]
1: Valid
Reference Information Support for Siemens

SND-RATE

Sets compression rate when compression rate in SEND is selected 'High'.
Setting values
0: Compression rate 1/16
1: Compression rate 1/20
2: Compression rate 1/24
[Factory settings and after RAM clear: 0]

CTM-S06

Setting for deleting password from export file of file transmission address
Settings
0: The password is not deleted.
1: The password is deleted.
[Factory setting/value after clearing RAM: 0]
When this item is set to "1," the password of the file transmission destination is deleted from the export file when the
address book data has been exported from the remote UI. (This is to prevent information leaks.)

FREG-SW

Selection of whether to display the free register area of the MEAP counter (for SEND)
Settings
0: The free register area is not displayed.
1: The free register area is displayed.
[Factory setting/value after clearing RAM: 0]
Memo:
- This is not used with normal servicing. (It is used for analyzing trouble causes).
- To use it, the instructions given by the quality support division must be followed.

Canon iR C3380 series, Service Manual

Search results

Summary of Contents for iR C3380 series

Reviews:

Related manuals for iR C3380 series

Brands by name

Popular brands