Canon IR5000 - iR B/W Laser Service Manual Download

Page: 124 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 2 ORIGINAL EXPOSURE SYSTEM

2-18 R

6.1.2 Mounting the Scanner Motor

1) Attach the belt [3] to the pulley [2] of

the scanner motor [1].

2) Fit the motor base to its position, fit the

two springs to provide tension to the
belt; then, secure it in place with three
screws.

F02-601-04

[3]

[2]

[1]

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands