Canon IR5000 - iR B/W Laser Service Manual Download

Page: 133 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 2 ORIGINAL EXPOSURE SYSTEM

2-27 R

8. PCBs

8.1 Removing the Fuse PCB

1) Remove the reader rear cover.
2) Remove the three screws [1], and detach

the fuse PCB [2].

3) Remove the screw [3], and disconnect

the three connectors [4]; then, detach
the fuse PCB [5].

F02-801-01

[3]

[4]

[5]

[4]

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands