Canon IR5000 - iR B/W Laser Service Manual Download

Page: 378 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 5 PICK UP/FEEDING SYSTEM

5-79 P

3) Remove the two mounting screws [4],

and detach the duplex feeding fan [5].

Be sure that the arrow indicat-
ing the direction of air is as in-
dicated when mounting the du-
plex feeldng fan.

F05-906-27

9.6.17 Mounting the Reversing Flapper Solenoid

1) Adjust the position of the solenoid us-

ing two screws [2] so that the drive le-
ver [1] is fully pushed when the sole-
noid turns on (i.e., the plunger is
drawn).

F05-906-28

[5]

[4]

[1]

[2]

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands