Canon IR5000 - iR B/W Laser Service Manual Download

Page: 422 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 6 FIXING SYSTEM

6-41 P

4.7.4 Removing the External Delivery Sensor

1) Remove the fixing/feeding unit from the

machine.

2) Remove the external delivery roller.
3) Remove the two sensors [1], and detach

the sensor support plate [2].

F06-407-07

4) Disconnect the connector [3], and de-

tach the external delivery sensor [4].

F06-407-08

[2]

[1]

[4]

[3]

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands