Canon IR5000 - iR B/W Laser Service Manual Download

Page: 446 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 7 EXTERNALS AND CONTROLS

7-21 P

5.4 PCBs

5.4.1 DC Controller PCB

1) Remove the rear upper cover.
2) Disconnect the 26 connectors, and re-

move the seven screws [1]; then, detach
the DC controller PCB [2].

F07-504-01

Keep the following three points in mind when replacing the PCBs:
•

Be sure to transfer the six EEP-ROMs from the old to new PCBs; at

that time, be sure to refer to the color of each round label attached to the
EEP-ROM for correct transfer.

•

Be sure to enter the values indicated on the label [3] on the new PCB in

service mode by making the following selections:

COPIER>ADJUST>HV-TR>D-PRE-TR
COPIER>ADJUST>HV-TR>D-HV-TR
COPIER>ADJUST>HV-SP>D-HV-SP
COPIER>ADJUST>DEVELOP>D-HV-DE

•

Be sure to transfer the shorting connector [4] of J303 on the PCB from

the old to new PCB. (Keep in mind that failure to do so will disable the
control panel indication.)

F07-504-02

[1]

[2]

Red (IC105)

Brown

(IC104)

Yellow

(IC109)

Blue

(IC127)

White (IC130)

Green (IC110)

J303

[3]

[4]

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands