Canon IR5000 - iR B/W Laser Service Manual Download

Page: 518 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 8 PAPER DECK

8-43 P

3.5 Electrical Mechanisms

3.5.1 Removing the Deck Driver PCB

1) Disconnect the deck from its host ma-

chine; then, remove the six screws, and
detach the rear cover.

2) Disconnect the eight connectors [1], and

remove the four screws [2]; then, detach
the deck driver PCB [3].

F08-305-01

3.5.2 Removing the Open Switch PCB

1) Disconnect the deck from the host ma-

chine, and push the latch plate [2] of the
compartment [1] with your finger to
open the compartment.

F08-305-02

[1]

[2]

[3]

(rear)

[2]

[1]

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands