manualshive.com logo in svg

Canon IR5000 - iR B/W Laser, Service Manual

The Canon IR5000 - iR B/W Laser is a high-quality printing device designed to meet all your business needs. With its impressive speed and advanced features, this multifunctional printer ensures exceptional performance. Need guidance on operating it? Download the free service manual from 88.208.23.73:8080 to maximize the potential of this outstanding machine.

Share
Download
background image

COPYRIGHT © 2000 CANON INC. 

2000 2000 2000 2000

 CANON iR5000/iR6000 REV.0 JULY 2000

2-2 T

CHAPTER 2 IMAGE ADJUSTMENT BASIC PROCEDURE

2. Making Checks on the Printer Unit (1/2)

Is there a 

difference in density between 

front and rear?

Is the rear lighter?

Turn the adjusting screw 
found at the front of the 
primary charging assembly 
clockwise. (2 full turns max.)

Turn the adjusting screw 
found at the rear of the 
primary charging assembly 
clockwise. (2 full turns max.)

Generate one print of a halftone image.

Is it foggy?

Are the readings ± 6 V 

of the target value?

(*1)

Are the readings 70 

± 

15 V?

<

Checking the Density Slope

>

<Checking fro Fogging>

YES

NO

YES

NO

YES

NO

NO

YES

NO

YES

YES

NO

Are there vertical 

lines in the image?

Are there vertical 

lines in the image?

<

Checking Images

>

  Checking Halftone Images

YES

YES

NO

NO

Execute forced 
potential control.

Generate a halftone image.

Generate a blank print.

Make the selections in service mode, and turn off 
and then on the main power switch: 
COPIER>FUNCTION>DPC>DPC.

Check the following readings in service mode:
COPIER>DISPLAY>DPOT>VL1M (for copier image)
COPIER>DISPLAY>DPOT>VL1M-P (for printer image)

Check the following readings in service mode:
COPIER>DISPLAY>DPOT>VL2M (for copier image)
COPIER>DISPLAY>DPOT>VL2M-P (for printer image)

Check the following readings in service mode:
COPIER>DISPLAY>DPOT>VDM (for copier image)
COPIER>DISPLAY>DPOT>VDM-P (for printer image)

A

Check the following, and replace them if 
necessary:
 1. Laser (for output)

2. Potential control system
3. Photosensitive drum

Check the following, and replace them if 
necessary.

1. Laser (for output)
2. Potential control system
3. Photosensitive drum

Check the primary charging 
system and the potential control 
system; if normal, replace the 
photosensitive drum.

Clean the following; also check 
for foreign matter:
 1. Dust-proofing glass

2. Charging assemblies

1. If there still is a difference in density after giving the adjusting screw 2 turns (each turn 
    causing a change of about 0.7 mm), check the scanning lamp and the scanner for soiling.
2. When making a clockwise turn, be sure that the intervals between wire grid runs are not 
    larger than 9 mm.
    When making a counterclockwise turn, be sure that the intervals between wire grid runs 
    are not smaller than 7.5 mm.
3. The machine will not execute potential control even when the main power switch is 
    turned off and then on if the temperature of the fixing assembly is 150˚C or higher.

-50     -40     -30    -20     -10        0        +10    +20    +30   +40    +50

Default

Lighter image

Darker image

    Adjusting the Offset of the VL Target Potential 
    (DE-OFFSET/DE-OFFSET-P)
    Vary the value using the following as a guide:
    COPIER>ADJUST>V-CONT>DE-OFST (for copier image)
    COPIER>ADJUST>V-CONT>DE-OFST-P (for printer image)

Adjust the offset value of the VL target potential.

Memo

Are the readings ± 6 V 

of the target value?

(*2)

REF.

*1:VD target value
  COPIER >DISPLAY >DPOT >VDT (for copier image)
  COPIER >DISPLAY >DPOT >VDT-P (for printer image)
*2:VL1 target value
  COPIER >DISPLAY >DPOT >VD1T (for copier image)
  COPIER >DISPLAY >DPOT >VD1T-P (for printer image)

Moving the wire from the photosensitive drum causes the image to be lighter, while 
moving it closer causes the images to be darker.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IR5000 - iR B/W Laser

Panasonic DP-3000 Technical Manual preview
DP-3000
Brand: Panasonic Pages: 342
Minolta EP3000 Manual preview
EP3000
Brand: Minolta Pages: 329
Gestetner 2135DP Operating Instructions Manual preview
2135DP
Brand: Gestetner Pages: 70
Gestetner 3220 Copier Manual preview
3220
Brand: Gestetner Pages: 90
Canon C3220 Copying Manual preview
C3220
Brand: Canon Pages: 372
Canon imageRUNNER ADVANCE DX C3835i Faq Manual preview
imageRUNNER ADVANCE DX C3835i
Brand: Canon Pages: 228

Brands by name

Popular brands

Load more brands