Canon IR5000 - iR B/W Laser Service Manual Download

Page: 570 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 3 STANDARDS AND ADJUSTMENTS

3-5 T

1.4 Adjusting the Image Leading Edge Margin

1) Adjust the image margin in service mode so that it is as indicated:

COPIER>ADJUST>Feed-ADJ>REGIST.

F03-104-01

1.5 Adjusting the Left/Right Non-Image Width

1) Adjust the non-image width in service mode so that it is as indicated:

COPIER>ADJUST>ADJ-XY>ADJ-Y.

F03-105-01

Edge of paper

Decreasing the REGIST setting

(A decrease by ‘10’ will increase the margin by 1 mm.)

Increasing the REGIST setting

(An increase by ‘10’ will decrease the margin by 1 mm.)

2.5mm±2.0

Edge of image

Increasing the ADJ-Y setting

(An increase by ‘12’ will increase

the non-image width by 1 mm.)

Decreasing the ADJ-Y setting

(A decrease by ‘12’ will

decrease the margin by 1 mm.)

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands