Canon IR5000 - iR B/W Laser Service Manual Download

Page: 645 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-32 T

c. E711-0003

Wrong operation

1) Turn off and then on the main power switch. Is the problem cor-

rected?

YES: Check the operation once again; if normal, end the work.

Connector, Remote diagnostic device PCB

2) Is the interface cable between the remote diagnostic device PCB

and the main controller PCB normal?

NO:

Correct the cable.

YES: Replace the remote diagnostic device PCB.

4.1.32 E712

Wrong operation

1) Turn off and then on the main power switch. Is the problem cor-

rected?

YES: Check the operation once again; if normal, end the work.

Connector

2) Is the cable between the ADF controller PCB and the reader con-

troller PCB normal?

NO:

Correct the cable.

ADF controller PCB, Reader controller PCB

3) Try replacing the ADF controller PCB. Is the problem corrected?

YES: End.
NO:

Replace the reader controller PCB.

4.1.33 E713

Wrong operation

1) Turn off and then on the main power switch.

YES: Check the operation once again; if normal, end the work.

Connectors

2) Is the interface cable between the finisher controller PCB and the

DC controller PCB normal?

NO:

Correct the cable.

Finisher controller PCB, DC controller PCB

3) Try replacing the finisher controller PCB. Is the problem cor-

rected?

YES: End.
NO:

Replace the DC controller PCB.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands