Canon IR5000 - iR B/W Laser Service Manual Download

Page: 738 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 5 SERVICE MODE

5-45 T

COPIER>ADJUST

F05-401-02

White

Original density

A lower setting decreases text density.

Copy density

A higher setting increases text density.

<AE>

Executing AE Adjustment
If you have cleared the RAM on the reader controller PCB, enter the settings indicated on

the service label.

AE-TBL

Use it to adjust the density of characters for image density adjustment.

Range of

1 to 9 Default: 5

adjustment

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands