Chapter 2
2-18
F-2-63
<Attaching the service book holder>
1) Remove the double-faced tape at the back of the service book holder
[1], and attach the holder to the bottom of the machine.
Points to Note
When attaching the service book holder to the machine, 6mm or more
space must be ensured between the front of the bottom sheet metal [2]
and the front of the service book holder. If the paper deck is attached
afterward without the space, the paper deck rail hits the service book
holder.
When attaching the paper deck at the same time, be sure to attach the
paper deck before the service book holder.
F-2-64
Prohibited area of affixation
- Inside the machine (inside the front cover)
- The area blocking the louver
- The area blocking the grip
<Attaching the Shut-Down Warning Label>
1) Pick out the Shut-Down Warning Label [1] prepared in the
appropriate language, and attach it to the bottom left side [3] of the
main power switch [2] of the machine's right cover (lower rear).
F-2-65
<Attaching the document size label>
1) Widen the document size plates [1] to the A4/A3 position, and attach
the label while matching the part A of the document size plate [1]
with the A4/A3 position of the ADF size label [2].
F-2-66
<Mounting the Touch Pen>
1) Set the touch pen on the control panel.
F-2-67
<Steps after the machine gets ready for installation>
1) Refer to the Installation Manual included with each option if
attaching the options such as the sorter.
2) Clean up around the machine.
3) Move the machine to the installation site, and fix the machine with the
2 adjusters.
Reference: Use a driver if the adjusters cannot be rotated by hand.
4) Enter requirements in the service book, and store it in the service book
holder.
[1]
[1]
[2]
[1]
6mm
[1]
[2]
[2]
[1]
A4
A3
A
[2]
[1]
[1]
Summary of Contents for iR5570 Series
