(2) Click [Add].
<Method for entering IPv4 addresses>
Specification
Method
Input Method
Input Example
Single Address
Enter the IP address, with the numbers separated by periods (.).
192.168.0.10
Multiple Addresses
To enter the IP addresses of consecutive numbers, place a hyphen (-)
between the address of the smallest number and that of the largest
number.
This setting specifies the range of IP addresses to be excepted.
This setting is useful when you want to specify a series of addresses at a
time.
192.168.0.10-
192.168.0.20
Prefix Address
To specify with a prefix (0 to 32), place a slash (/) between the prefix
address and the prefix length.
This setting specifies the prefix to be excepted.
This setting is useful when you want to specify addresses having the same
prefix at a time.
192.168.0.10/24
Up to 16 addresses (or 16 ranges of addresses) can be specified for the single address, multiple addresses, and prefix
address combined.
An address consisting of only zeros cannot be specified.
<Method for entering IPv6 addresses>
Specification
Method
Input Method
Input
Example
Single Address
Enter the IP address, with the alphanumeric characters separated by a colon (:).
fe80::10
Multiple Addresses
To enter the IP addresses of consecutive numbers, place a hyphen (-) between
the address of the smallest number and that of the largest number.
This setting specifies the range of IP addresses to be excepted.
This setting is useful when you want to specify a series of addresses at a time.
fe80::10-
fe80::20
Prefix Address
To specify with a prefix (0 to 128), place a slash (/) between the prefix address
and the prefix length.
This setting specifies the prefix to be excepted.
This setting is useful when you want to specify addresses having the same prefix
at a time.
fe80::10/64
㻟㻠㻢㻌㻛㻌㻡㻝㻠
Summary of Contents for LBP7100Cn
