4
4
4-3
4-3
Error Code > Service Error Code
Error Code > Service Error Code
User Error Code
No. T/R
Description
#001 [T] an original has jammed.
#003 [T/R] tine-out for copying or sending/receiving a single page has occurred.
#005 [T/R] time-out for initial identification (T0/T1) has occurred.
#008 [R] a mismatch of passwords at time of polling transmission has occurred.
#009 [R] recording paper has jammed or is absent.
#012 [T] recording paper is absent at the other party.
#018 [T/R] auto call initiation has failed.
#022 [T] call initiation has failed.
#037 [R] image memory overflow at time of reception has occurred.
#080 [T] the other party has no F code reception function/or is not set to receive it.
#081 [T] the other party has no password reception function/or is not to receive it.
#099 [T/R] the Stop key is pressed while a communication is under way.
#102 [T/R] a mismatch of F-code/password has occurred.
#995 [T/R] a memory communication reservation has been cancelled.
T-4-1
Service Error Code
No. T/R
Description
##100 [T] at time of transmission, the procedural signal has been transmitted more than
specified.
##101 [T/R] the modem speed does not match that of the other party.
##102 [T] at time of transmission, fall-back cannot be used.
##103 [R] at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).
##104 [T] at time of transmission, RTN or PIN is received.
##106 [R] at time of reception, the procedural signal is received for 6 sec while in wait for the
signal.
##107 [R] at time of reception, the transmitting party cannot use fall-back.
##109 [T] at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received,
and the procedural signal has been sent more than specified.
##111 [T/R] memory error has occurred.
##114 [R] at time of reception, RTN is transmitted.
##200 [R] at time of reception, no image carrier is detected for 5 sec.
##201 [T/R] DCN is received outside the normal parity procedure.
##204 [T] DTC without transmission data is received.
##220 [T/R] system error (main program out of control) has occurred.
##223 [T/R] while a communication is under way, the line is cut.
##224 [T/R] in G3 communication, an error has occurred in the procedural signal.
##226 [T/R] the stack printer has fallen outside the RAM area.
##229 [R] the recording unit has remained locked for 1 min.
##232 [T] encoding error has occurred.
##237 [R] decoding error has occurred.
##238 [R] the print control unit is out of order.
##261 [T/R] system error has occurred.
##280 [T] at time of transmission, the procedural signal has been transmitted more than
specified.
##281 [T] at time of transmission, the procedural signal has been transmitted more than
specified.
##282 [T] at time of transmission, the procedural signal has been transmitted more than
specified.
##283 [T] at time of transmission, the procedural signal has been transmitted more than
specified.
##284 [T] at time of transmission, DCN is received after transmission of TCF.
##285 [T] at time of transmission, DCN is received after transmission of EOP.
##286 [T] at time of transmission, DCN is received after transmission of EOM.
##287 [T] at time of transmission DCN is received after transmission of MPS.
##288 [T] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
##289 [T] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
##290 [T] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
