Canon VarioPrint 6000 Series Operation Manual Download | Manualshive

Page: 255 / 354

background image

Media related actions

Load the media

Introduction

This section describes how to load the media into a paper tray.

When you load the media via the [Load] button in the [Schedule], the paper tray is automatically
assigned to the correct media.

When you load and assign the media via the [Assign] button in the [Trays] view, you must assign
the paper tray to the loaded media manually.

When no external finisher is connected to the machine, you must put all the media types face up
and header up into the paper trays. The tabs of tab sheets must be at the right-hand side. When
an external finisher is connected to the machine, it is possible that you must put the media into
the paper trays in a different way. Refer to the documentation of the external finisher for more
information about how to place the media.

When to do

• The [Schedule] displays a red bar next to a required media. The red bar indicates that a

scheduled job now requires a media that is not available in the paper trays.

• The [Schedule] displays an orange bar next to a required media. The orange bar indicates that

a scheduled job requires media which is either not available in the paper trays or which is
available, but not in sufficient quantity to finish the job.

• The current job requires more of the same media than is currently loaded in the paper trays.

You can add more of the required media into another paper tray.

• You already want to load and assign media that are required for the next job (work ahead).

IMPORTANT

Always put the stack of media at the left-hand side of the paper guides inside the paper trays, as

indicated on the sticker inside the paper trays.

Procedure

1.

Put a small stack of the media into the paper tray.

2.

Pinch the green handle of the right-hand guide and push the guide against the edge of the media.

3.

Turn the green knob to adjust the front guide and the rear guide.

4.

Put the rest of the media on top of the small stack.

NOTE

When you want to assign the media later you must press the [Not assigned] button.

Media related actions

Chapter 11 - Media handling

255

VarioPrint 6000 line

«
...
253
254
255
256
257
...
»

Summary of Contents for VarioPrint 6000 Series



































































































































































































































































































































































Reviews:

No comments

Related manuals for VarioPrint 6000 Series

Brand: Nakajima Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands