manualshive.com logo in svg

Canon VK-16 v2.1, Administrator'S Manual

The Canon VK-16 v2.1 Administrator's Manual is a comprehensive guide designed to assist users in efficiently operating and managing this exceptional product. This manual is available for free download from 88.208.23.73:8080, offering users a convenient resource to optimize their VK-16 v2.1 experience.

Share
Download
background image

10-3

App

endi

x

Hard Disk

Lifetime of Hard Disk

A hard disk is a storage device that works physically, and has a limited lifetime. It is a kind of consumables. It is 
said that the average lifetime of a RAID system composed of SCSI hard disks is three years. However, this 
lifetime is considered to be true for standard file servers or business servers. The disk failure rate of VK-64/
VK-16 systems is higher than that of general file servers. It is reasonable to assume that the lifetime of hard 
disks in a VK-64/VK-16 system is about half of that of a standard file server (one and a half years).

Therefore, when you build a VK-64/VK-16 system, it is advisable to provide a hot-spare (spare hard disks that 
are active) for RAID configuration.

RAID Reconfiguration

If one of hard disks in RAID1 and RAID5 systems breaks down, you can restore the system by replacing the 
broken hard disk before other disks break.

Restoring the data stored on the broken hard disk after replacement is referred to as rebuilding.

During RAID rebuilding, a recording error may occur because disk system performance deteriorates.

RAID Rebuilding Time

When a failure occurs in a hard disk in a RAID system and you want to replace it with a hot-spare or new one, 
the rebuilding time is to be considered as follows: 

• Rebuilding takes about one minute per 1GB when no I/O is performed in a SCSI RAID card.

• When a RAID system is composed of four SCSI hard disks of 300GB each, the total disk size of the 

hard disks is 1200GB. To rebuild this system, 1200 minutes (20 hours) are required on the condition 
that there no I/O is performed.

• If rebuilding takes 20 hours when there is no I/O, the rebuilding time for a VK-64/VK-16 system where 

I/O is continuously performed can be assumed to be about 20 x 2 hours. Thus, when you perform 
rebuilding without stopping recording, it takes about 40 hours.

• There is no problem if rebuilding only takes a long time. However, the other hard disks may break 

down one after another during such rebuilding. If another hard disk breaks down during rebuilding, 
all of the stored data will be lost. Therefore, it is preferable to reduce rebuilding time as far as 
possible.

VK-64_SysManual_Ev21.book  3 ページ  ２００９年３月２日　月曜日　午後１時３分

CO

PY

Summary of Contents for VK-16 v2.1

































































































































































































































































































Reviews:

No comments

Related manuals for VK-16 v2.1

Ubiquiti Bullet Quick Start Manual preview
Bullet
Brand: Ubiquiti Pages: 40
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Brand: Ensemble Designs Pages: 19
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
Juniper EX2500 Quick Start preview
EX2500
Brand: Juniper Pages: 2
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Brand: TDK Pages: 13
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
ZALMAN CNPS5700D-Cu User Manual preview
CNPS5700D-Cu
Brand: ZALMAN Pages: 7
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140
NAMCO SOUL CALIBUR II Manual preview
SOUL CALIBUR II
Brand: NAMCO Pages: 26
INNOSILICON T3-43T User Manual preview
T3-43T
Brand: INNOSILICON Pages: 11
NZXT RESPIRE T40 Manual preview
RESPIRE T40
Brand: NZXT Pages: 2
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Microtek MiniLink Operation Manual preview
MiniLink
Brand: Microtek Pages: 25
Ubiquiti UniFi AP PRO Quick Start Manual preview
UniFi AP PRO
Brand: Ubiquiti Pages: 20
Altera Cyclone IV GX Reference Manual preview
Cyclone IV GX
Brand: Altera Pages: 40
Milesight Pro UR32 Quick Start Manual preview
Pro UR32
Brand: Milesight Pages: 15
TRENDnet TE100S8P - Fast Ethernet Switch (Spanish) Quick Installation Manual preview
TE100S8P - Fast Ethernet Switch
Brand: TRENDnet Pages: 11

Brands by name

Popular brands

Load more brands