Capetti Elettronica WineCap WSD12T-IIDR User Manual Download

Page: 6 / 9

WSD12T-IIDR

User Manual

WA0295E_WSD12T-IIDR_User Manual_R05

V4.6

CAPETTI ELETTRONICA s.r.l.  - Strada Stratta 57
10090 CASTIGLIONE TORINESE  -  TORINO  -  ITALY
VAT 04837130014 - Phone 011.981.98.11 -  Fax 011.981.98.210
e-mail info@capetti.it  -  web www.capetti.it

6/9

Shutting off/Reactivating the device.

If the device is shut off and left unused for a long time, you can issue the

STANDBY

command (

refer to

Picture 5 - Commands table

). Its

corresponds to the command number 4 and must be issued twice to confirm the operation.

Position the

WineCapKey

in the spot indicated in

Picture 4 - WineCapKey positioning

and wait for four

AMBER

flashes, then remove

the

WineCapKey

from device.

Verify that the device asks for confirmation of

STANDBY

command with alternate

GREEN/RED

flashing, then position again the

WineCapKey

and wait for four flashes again. The device will confirm the

STANDBY

status lighting the

RED

led for 2 seconds twice.

To reactivate the device the

TEST

command must be issued.

Summary of Contents for WineCap WSD12T-IIDR










Search results

Summary of Contents for WineCap WSD12T-IIDR

Reviews:

Related manuals for WineCap WSD12T-IIDR

Brands by name

Popular brands

Capetti Elettronica WineCap WSD12T-IIDR, User Manual

Search results

Summary of Contents for WineCap WSD12T-IIDR

Reviews:

Related manuals for WineCap WSD12T-IIDR

Brands by name

Popular brands