background image

 

WSD12T-IIDR 

User Manual

 

 

 

 

 

WA0295E_WSD12T-IIDR_User Manual_R05 

V4.6

 

 

CAPETTI ELETTRONICA s.r.l.  -   Strada Stratta 57 
10090 CASTIGLIONE TORINESE  -  TORINO  -  ITALY 
VAT 04837130014 - Phone 011.981.98.11 -  Fax 011.981.98.210 
e-mail info@capetti.it  -  web www.capetti.it

 

 

 

7/9

 

 

9.

 

Technical Information. 

Power supply

 

5.8A/h - 3.6 V type “C” lithium internal battery 

Battery life (*)

 

Up to 5years  

(samples every  60 minutes and radio signal quality at least sufficient)

 

 

Measures acquired 

(3 input channels

 

 

Horizontal axis rotation, parallel to surface 

 

Outdoor temperature 

Sampling interval 

(

*

)

 

Selectable from one minute to 24 hours 

(60 minutes default)

 

Datalogger capacity

 

64,000  samples

 

(

for each channel

)

 

Working temperature

 

 

Operative: -30°C ÷ +60°C 

 

Warehousing: -40°C ÷ +70°C  

Radio frequency

 

ISM 868MHz

 

Radio coverage

 

Up to 6Km in line of sight 

(can be extended usin

WR12

 battery powered routers)

 

Sealing

 

 

Datalogger: IP65 

 

Transducers: IP68 

Dimensions

 

 

Datalogger: 90 x 120 x 50mm 

 

Transducers: 140x55x32mm (

with 116mm fixing pace and 

±4°gross correction

Weight

 

 

Datalogger: 325g 

 

Transducers: 440g 

Case material

 

 

Datalogger: ABS 

 

Transducers: galvanized iron bracket covered with 
polybutadiene resin 

Mounting

 

 

Datalogger: fix on 4 points 

 

Transducers: fix on 2 points with ±4° gross correction 

Connections 

Wireless/USB/3m cable lenght for each transducer 

Inclination - Transducer type 

Uniaxial - MEMS technology - 1°÷15° Dual Range Automatic 
Autoscale  

Inclination - Measure range

 

±1°/±15° 

Inclination - Measure accuracy

 

± 0.5% of sample 

Inclination - Measure resolution

 

0.001° (

±1° range

) - 0.01° (

±15° range

Inclination - Mechanical zero adjustment 

± 2° gross setting (

micrometric with optional kit 

FIX-WSD15

) 

Inclination - Cross-axis sensitivity 

4% maximum 

Inclination - Temperature variation sensibility

 

±0.013%/°C temperature balance using 3° polynomial 

Inclination - Shock resistance

 

20,000g 

Inclination - Measure axis

 

Abscissa 

Inclination - Linearity 

±0.057° in measuring range 

Inclination - Over time stability 

Excellent 

Temperature - Transducer type 

NTC10KΩ 

Temperature - Measure range 

-30°C ÷ +60°C 

Temperature - Measure accuracy 

 

± 0.5°C  Range -30°C ÷ 0°C 

 

± 0.2°C  Range 0°C ÷ +60°C 

Temperature - Measure resolution 

0.01°C 

* battery life may be influenced by fieldwork conditions, sampling interval and system configuration

** radio coverage reachable using up to 3

WR12 routers

 (maximum 16 for each path) between the device and the basestation. 

 

 

 

Summary of Contents for WineCap WSD12T-IIDR










Reviews: