background image

 

 

 

 

 

 

 

 

WA0239E_WSD12T-AV_User Manual_R02 

 

CAPETTI ELETTRONICA s.r.l.  -   Strada Stratta 57 
10090 CASTIGLIONE TORINESE  -  TORINO  -  ITALY 
VAT 04837130014 - Phone 011.981.98.11 -  Fax 011.981.98.210 
e-mail info@capetti.it  -  web www.capetti.it

 

 

 

8/8

 

 

WSD12T-AV 

User Manual 

11.

 

Reference standards. 

EN 61010 -1 

 

For electromagnetic compatibility 
 

EN 61000 - 3 - 2 
EN 61000 - 3 - 3 
EN 300 220 -2 
EN 301 489 - 03 
EN 61000 - 6 -1 

 

 

 

 

 

 

 

 
 

 

 

 

 

This symbol indicates that this product is compliant with the European Directive 2011/65/CE that restricts 
the use of substances in the manufacturing of electronic devices.

 

 

 

 

 

 

The “WEEE” logo on the label  indicates that this product is compliant with the "WEEE" EC Directive.This 
symbol (valid only in the European Union countries) indicates that the product it is applied to, MUST NOT 
be  discarded  with  ordinary  household  or  industrial  waste,  but  must  be  sent  to  an  authorized  reception 
point. The end user should contact the device provider, either the manufacturer or the reseller, in order to 
agree a collection and disposal process, after having checked the terms and conditions of sale.

 

 

 

 

 

The features shown may be subject to change without notice.

 

  

Summary of Contents for WSD12T-AV









Reviews: