powers on a damp sponge or cloth. Rub lightly.
Rinse thoroughly and dry. If food has burned onto
the oven and is difficult to remove, soak the spots
with a cloth saturated with household ammonia.
Allow it to soak for an hour or two, with the door
closed. The food soil should be easy to remove
with a damp soapy cloth or mild abrasive.
OVEN RACKS AND ROLLERS
The oven racks and rollers are chrome plated steel.
Chrome cleaners
, such as Soft Scrub®, Cameo
or Bar Keepers Friend can be applied with a
damp sponge following package directions.
Rinse and dry. Powdered cleaners such as Bon-
Ami® or Comet are applied with a damp sponge
or cloth, rubbed lightly, rinsed and dried. Harsh
Cleaners which are commercial oven cleaners,
such as Easy Off® or Dow can be used on the
racks. However, some commercial oven cleaner’s
cause darkening and discoloration. Test the
cleaner on a small part of the rack and check
for any discoloration before cleaning the entire
rack. Allow to stand for 15 to 20 minutes. Rinse
thoroughly and dry.
FRAMES, SIDES, DOOR EXTERIOR, HEAT DEFLECTOR
These parts are made of stainless steel, follow the
directions for the Backguard (see page 28). Take
care when cleaning the door top, and do not let
water or cleaners run down the vents. If water or
cleaners spill into the vents, they may streak the
glass inside the door.
DOOR GASKET
Use a general kitchen spray cleaner, such as
Formula 409® or Fantastik®. Spray it and blot
dry with a cloth. Do not rub. Do not remove or
damage the mesh.
OVEN LIGHT BULB REPLACEMENT
For oven light bulb replacement use only a 40 watt,
120 volt appliance light bulb. These are available in
supermarkets. DO NOT use a standard light bulb in
any oven, the heat will break it.
TO REPLACE THE LIGHT BULB:
1. Be sure the oven light bulb switch is the off
position The bottom of the switch is pressed in.
Let the cover and the bulb cool completely.
2. Remove the light cover, Turn the cover to the
left (counterclockwise) to unscrew it.
3. Remove the burnt out bulb. Replace it with a 40
watt appliance light bulb only.
4. Replace cover. Turn circuit breaker back on, if
turned off. (See Caution below).
CAUTION: Be sure the oven light switch (see page
8, # 11) is in the OFF position and the cover is
cool. If the bulb comes loose from the base, turn
off the power to the oven at the circuit breaker
panel, before attempting to remove the bulb base
from the socket.
POWER FAILURE
The broiler and oven burners cannot be turned
on during a power failure. To light the sealed top
burners, turn the control knob to “lite” hold a lighted
match to the port ring. After the flame is burning
all the way around the burner, adjust the flame to
the desired height. It is necessary to light each
burner individually. Do not light more than one
burner at a time.
C A R E A N D M A I N T E N A N C E
Summary of Contents for Precision Series GSCR604GW
